參數資料
型號： AAT3690
廠商： Advanced Analog Technology,lnc.
英文描述： 1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger
中文描述： 安培USB接口/適配器鋰離子電池充電器
文件頁數： 15/20頁
文件大小： 425K
代理商： AAT3690
AAT3690
1.0A USB Port/Adapter
Lithium-Ion/Polymer Battery Charger
3690.2007.01.1.2
15
Battery Charge Status Indication
The AAT3690 has two status LED driver outputs.
These two LEDs can indicate simple functions
such as no battery charge activity, battery charg-
ing, charge complete, and charge fault.
Status Indicator Display
Simple system charging status may be displayed
using one or two LEDs in conjunction with the STAT1
and STAT2 pins on the AAT3690. These two pins are
simple switches to connect the LED cathodes to
ground. It is not necessary to use both display LEDs
if a user simply wants to have a single lamp to show
"charging" or "not charging." This can be accom-
plished by using the STAT1 pin and a single LED.
Using two LEDs and both STATpins simply gives the
user more information to the charging states. Refer
to Table 2 for LED display definitions.
The LED anodes should be connected to either
V
USB
or V
ADP
, depending upon the system design
requirements. The LEDs should be biased with as
little current as necessary to create reasonable illu-
mination; therefore, a ballast resistor should be
placed between the LED cathodes and the
STAT1/2 pins. LED current consumption will add to
the overall thermal power budget for the device
package, so it is wise to keep the LED drive current
to a minimum. 2mA should be sufficient to drive
most low-cost green or red LEDs. It is not recom-
mended to exceed 8mA for driving an individual
status LED. The required ballast resistor value can
be estimated using the following formulas:
For connection to the adapter supply:
Example:
Note: Red LED forward voltage (V
F
) is typically
2.0V @ 2mA.
For connection to the USB supply:
Example:
Note: Green LED forward voltage (V
F
) is typically
3.2V @ 2mA.
The status LED display conditions are described in
Table 2.
R
B(STAT2)
=
= 900
Ω
5.0V - 3.2V
2mA
R
B(STAT1/2)
= V
USB
- V
F(LED)
I
LED(STAT1/2)
R
B(STAT1)
=
= 1.75k
Ω
5.5V - 2.0V
2mA
R
B(STAT1/2)
= V
ADP
- V
F(LED)
I
LED(STAT1/2)
Table 2: Status LED Display Conditions.
Event Description
STAT1
STAT2
Charge Disabled or Low Supply
Charge Enabled Without Battery
Battery Charging
Charge Completed
Fault
Off
Off
Flash
1
On
Off
On
Flash
1
Off
On
On
1. Flashing rate depends on output capacitance.
相關PDF資料
PDF描述
AAT3690IWP-4.2-T1 1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger
AAT3697 2A Lithium-Ion/Polymer Battery Charger
AAT3697IWP-4.2-T1 2A Lithium-Ion/Polymer Battery Charger
AAT4280AIJS-1-T1 Slew Rate Controlled Load Switch
AAT4280AIJS-2-T1 Slew Rate Controlled Load Switch
相關代理商/技術參數
參數描述
AAT3690IWP-4.2-T1 制造商:Advanced Analogic Tech 功能描述:AAT3690 Series 4 - 5.5 V 1A USB Port/Adapter Lithium-Ion/Polymer Battery Charger 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3690 Series 4 - 5.5 V 1A USB Port/Adapter Lithium-Ion/Polymer Battery Charger 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC
AAT3691IRN-4.2-T1 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3691 Series 1.6 A 28 V Dual Input 1.6 A Linear Charger - TDFN-16
AAT3692IRN-4.2-T1 功能描述:電池管理 2 Input 1.6A Linear Chrg w/28V OVP RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
aat3693idh-aa-db1 制造商:Skyworks Solutions Inc 功能描述:AAT3693 Series 1.6 A Lithium-Ion/Polymer Battery Charger Eval Board
AAT3693IDH-AA-T1 功能描述:電池管理 Lithium-Ion/Polymer Batt Charger 1.6A RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*