- 您現在的位置：買賣IC網 > PDF目錄381238 > AAT3688IWP-4.2-T1 (Advanced Analog Technology,lnc.) USB Port Lithium-Ion/Polymer Battery Charger PDF資料下載
參數資料
| 型號： | AAT3688IWP-4.2-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | USB Port Lithium-Ion/Polymer Battery Charger |
| 中文描述： | USB接口鋰離子電池充電器 |
| 文件頁數： | 14/23頁 |
| 文件大小： | 522K |
| 代理商： | AAT3688IWP-4.2-T1 |
AAT3688
USB Port Lithium-Ion/Polymer Battery Charger
14
3688.2006.10.1.5
USB Input Charge Inhibit and Resume
The AAT3688 UVLO and power on reset feature
will function when the USB input pin voltage level
drops below the UVLO threshold. At this point, the
charger will suspend charging and shut down.
When power is re-applied to the USB pin or the
UVLO condition recovers, the system charge con-
trol will assess the state of charge on the battery
cell and will automatically resume charging in the
appropriate mode for the condition of the battery.
Enable / Disable
The AAT3688 provides an enable function to con-
trol the charger IC on and off. The enable (EN) pin
is an active high. When pulled to a logic low level,
the AAT3688 will be shut down and forced into the
sleep state. Charging will be halted regardless of
the battery voltage or charging state. When the
device is re-enabled, the charge control circuit will
automatically reset and resume charging functions
with the appropriate charging mode based on the
battery charge state and measured cell voltage.
Programming Charge Current
The fast charge constant current charge level for the
USB input is programmed with set resistors placed
between the USBH and USBLpins and ground. The
accuracy of the fast charge, as well as the precondi-
tioning trickle charge current, is dominated by the
tolerance of the set resistors used. For this reason,
1% tolerance metal film resistors are recommended
for programming the desired constant current level.
The USB input fast charge constant current charge
control provides for two current set levels, USBH
and USBL. The USBSEL pin is used to select the
high or low charge current levels in the USB charge
mode. When the USBSEL pin is pulled to a voltage
level above the V
USBSEL(H)
threshold, the USBH cur-
rent level will be selected. Conversely, this pin
should be pulled below the V
USBSEL(L)
to enable the
USBL charge level. Typically, the two R
SETH
and
R
SETL
for the USBH and USBL functions are fixed
for 500mA and 100mA USB fast charge levels.
However, these two charge levels may be set to any
level between 50mA and 500mA, depending upon
the system design requirements for a given USB
charge application. Refer to Table 1 and Figure 3
for recommended R
SETH
and R
SETL
values.
Figure 3: I
FASTCHARGE
vs. R
SET
.
Protection Circuitry
Over-Voltage Protection
An over-voltage event is defined as a condition
where the voltage on the BAT pin exceeds the
maximum battery charge voltage and is set by the
over-voltage protection threshold (V
OVP
). If an
over-voltage condition occurs, the AAT3688 charge
control will shut down the device until voltage on
the BAT pin drops below the over-voltage protec-
tion threshold (V
OVP
). The AAT3688 will resume
normal charging operation after the over-voltage
condition is removed. During an over-voltage
event, the STAT LEDs will report a system fault; the
actual fault condition may also be read via the
DATA pin signal.
Over-Temperature Shutdown
The AAT3688 has a thermal protection control cir-
cuit which will shut down charging functions should
the internal die temperature exceed the preset
thermal limit threshold.
R
SET
(k
Ω
Ω
)
I
F
10
100
1000
1
10
100
1000
USBL
USBH
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3689 | 0.5A/1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3689IWP-4.2-T1 | 0.5A/1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3690 | 1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3690IWP-4.2-T1 | 1.0A USB Port/Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3697 | 2A Lithium-Ion/Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3690IWP-4.2-T1 | 制造商:Advanced Analogic Tech 功能描述:AAT3690 Series 4 - 5.5 V 1A USB Port/Adapter Lithium-Ion/Polymer Battery Charger 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3690 Series 4 - 5.5 V 1A USB Port/Adapter Lithium-Ion/Polymer Battery Charger 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3691IRN-4.2-T1 | 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3691 Series 1.6 A 28 V Dual Input 1.6 A Linear Charger - TDFN-16 |
| AAT3692IRN-4.2-T1 | 功能描述:電池管理 2 Input 1.6A Linear Chrg w/28V OVP RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| aat3693idh-aa-db1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3693 Series 1.6 A Lithium-Ion/Polymer Battery Charger Eval Board |
| AAT3693IDH-AA-T1 | 功能描述:電池管理 Lithium-Ion/Polymer Batt Charger 1.6A RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。