- 您現在的位置：買賣IC網 > PDF目錄381238 > AAT3687 (Advanced Analog Technology,lnc.) Lithium-Ion/Polymer Battery Charger PDF資料下載
參數資料
| 型號： | AAT3687 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Lithium-Ion/Polymer Battery Charger |
| 中文描述： | 鋰離子電池充電器 |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 526K |
| 代理商： | AAT3687 |
AAT3687
Lithium-Ion/Polymer Battery Charger
10
3687.2006.10.1.7
Charging Operation
The AAT3687 has four basic modes for the battery
charge cycle: pre-conditioning / trickle charge; con-
stant current / fast charge; constant voltage; and
end of charge (see Figure 1.) (AAT3687-2 does not
have trickle charge.)
Battery Preconditioning
Before the start of charging, the AAT3687 checks
several conditions in order to assure a safe charging
environment. The input supply must be above the
minimum operating voltage, or under-voltage lockout
threshold (V
UVLO
), for the charging sequence to
begin. Also, the cell temperature, as reported by a
thermistor connected to the TS pin from the battery,
must be within the proper window for safe charging.
When these conditions have been met and a battery
is connected to the BAT pin, the AAT3687 checks the
state of the battery. If the cell voltage is below the
preconditioning voltage threshold (V
MIN
), the charge
control begins preconditioning the cell.
The battery preconditioning trickle charge current is
equal to the fast charge constant current divided by
10. For example, if the programmed fast charge
current is 1.5A, then the preconditioning mode
(trickle charge) current will be 150mA. Cell precon-
ditioning is a safety precaution for deeply dis-
charged battery cells and also aids in limiting power
dissipation in the pass transistor when the voltage
across the device is at the greatest potential.
Fast Charge / Constant Current Charging
Battery cell preconditioning continues until the volt-
age on the BAT pin exceeds the preconditioning
voltage threshold (V
MIN
). At this point, the AAT3687
begins the constant current fast charging phase.
The fast charge constant current (I
CC
) amplitude is
programmed by the user via the R
SET
resistor. The
AAT3687 remains in the constant current charge
mode until the battery reaches the voltage regula-
tion point, V
BAT
.
Constant Voltage Charging
The system transitions to a constant voltage charg-
ing mode when the battery voltage reaches the
output charge regulation threshold (V
BAT
) during
the constant current fast charge phase. The regu-
lation voltage level is factory programmed to 4.2V
(±1%). Charge current in the constant voltage
mode drops as the battery cell under charge reach-
es its maximum capacity.
End of Charge Cycle Termination and Recharge
Sequence
When the charge current drops to 7.5% of the pro-
grammed fast charge current level in the constant
voltage mode, the device terminates charging and
goes into a sleep state. The charger will remain in
a sleep state until the battery voltage decreases to
a level below the battery recharge voltage thresh-
old (V
RCH
).
When the input supply is disconnected, the charg-
er will automatically transition into a power-saving
sleep mode. Only consuming an ultra-low 0.3
μ
A in
sleep mode (1
μ
A for AAT3687-1 and AAT3687-2),
the AAT3687 minimizes battery drain when it is not
charging. This feature is particularly useful in appli-
cations where the input supply level may fall below
the battery charge or under-voltage lockout level.
In such cases where the AAT3687 input voltage
drops, the device will enter sleep mode and auto-
matically resume charging once the input supply
has recovered from the fault condition.
Figure 1: Current vs. Voltage Profile During Charging Phases.
Constant Current
Charge Phase
Constant Voltage
Charge Phase
Preconditioning
Trickle Charge
Phase
Charge Complete Voltage
Constant Current Mode
Voltage Threshold
Regulated Current
Trickle Charge and
Termination Threshold
I = CC / 10
I = Max CC
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3687IWP-4.2-1-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3687IWP-4.2-2-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3687IWP-4.2-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3688 | USB Port Lithium-Ion/Polymer Battery Charger |
| AAT3688IWP-4.2-T1 | USB Port Lithium-Ion/Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3687IWP-4.2-1-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3687IWP-4.2-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3688AIWP-4.2-DB1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3688 Series USB Port Lithium-Ion/Polymer Battery Charger Evaluation Board |
| AAT3688AIWP-4.2-T1 | 制造商:Skyworks Solutions Inc 功能描述:Battery Management 1A USB Port LI-Ion Polymer Battery Chgr 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3688IWP-4.2-T1 | 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3688 Series 5.5 V USB Port Lithium-Ion/Polymer Battery Charger - TDFN33-12 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
發布緊急采購，3分鐘左右您將得到回復。