- 您現在的位置：買賣IC網 > PDF目錄381238 > AAT3686IXN-4.2-T1 (Advanced Analog Technology,lnc.) USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger PDF資料下載
參數資料
| 型號： | AAT3686IXN-4.2-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
| 中文描述： | USB接口/ AC適配器鋰離子電池充電器 |
| 文件頁數： | 10/24頁 |
| 文件大小： | 528K |
| 代理商： | AAT3686IXN-4.2-T1 |
Functional Block Diagram
Charge
Control
Current
Compare
Reverse Blocking
Reverse Blocking
CV/
Precharge
USB
USBSEL
USBH
USBL
Constant
Current
Current
Compare
ADP
BAT
ADPSET
UVLO
Over-
Temperature
Protect
Charge
Status
STAT2
STAT1
TS
Window
Comparator
80μA
Serial
Data
DATA
Watchdog
Timer
CT
GND
Charge
Reduction
Loop
CHR
Voltage
Sense
ADPP#
EN
IC enable
AAT3686
USB Port/AC Adapter
Lithium-Ion/Polymer Battery Charger
10
3686.2006.10.1.9
Functional Description
The AAT3686 is a highly integrated single-cell lithium-
ion/polymer battery charger IC designed to operate
with USB port and AC adapter inputs, while requiring
a minimum number of external components. The
AAT3686 precisely regulates battery charge voltage
and current for 4.2V lithium-ion/polymer battery cells.
The adapter charge input constant current level can
be programmed up to 1.5A for rapid charging appli-
cations. In the absence of a high current adapter
input source, the AAT3686 can be powered from a
USB port V
BUS
supply. Depending on the USB port
type, the AAT3686 constant charge current can be
externally programmed for two levels, USB high and
USB low, for maximum constant current charge lev-
els up to 500mA. Typically, the USB charge levels
are set at 500mA and 100mA for the USBH and
USBL modes; however, the user may program
either mode to any level up to 500mA.
The USBH/Lmode has automatic Charge Reduction
Loop control to allow users to charge the battery with
limited available current from a USB port, while
maintaining the regulated port voltage. This system
assures the battery charge function will not overload
a USB port while charging if other system demands
also share power with the respective port supply.
The USB charge function is automatically disabled
when an adapter input power source greater than
4.4V is present.
Status monitor output pins are provided to indicate
the battery charge status by directly driving two
external LEDs. A serial interface output is available
to report 22 various status states to a microcontroller.
Battery temperature and charge state are fully mon-
itored for fault conditions. In the event of an over-
voltage or over-temperature failure, the device will
automatically shut down, thus protecting the charg-
ing device, control system, and the battery under
charge. In addition to internal charge controller ther-
mal protection, the AAT3686 also provides a tem-
perature sense feedback function (TS pin) from the
battery to shut down the device in the event the bat-
tery exceeds its own thermal limit during charging.
All fault events are reported to the user either by the
simple status LEDs or via the DATA pin function.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3687 | Lithium-Ion/Polymer Battery Charger |
| AAT3687IWP-4.2-1-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3687IWP-4.2-2-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3687IWP-4.2-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3688 | USB Port Lithium-Ion/Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3687IWP-4.2-1-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3687IWP-4.2-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3688AIWP-4.2-DB1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3688 Series USB Port Lithium-Ion/Polymer Battery Charger Evaluation Board |
| AAT3688AIWP-4.2-T1 | 制造商:Skyworks Solutions Inc 功能描述:Battery Management 1A USB Port LI-Ion Polymer Battery Chgr 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3688IWP-4.2-T1 | 制造商:SKYWORKS SOLUTIONS 功能描述:AAT3688 Series 5.5 V USB Port Lithium-Ion/Polymer Battery Charger - TDFN33-12 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
發布緊急采購，3分鐘左右您將得到回復。