參數資料
型號： AAT3685IWP-4.2-T1
廠商： Advanced Analog Technology,lnc.
英文描述： Lithium-Ion/Polymer Battery Charger
中文描述： 鋰離子電池充電器
文件頁數： 15/23頁
文件大?。?/td> 557K
代理商： AAT3685IWP-4.2-T1
Figure 3: I
FASTCHARGE
vs. R
SET
.
Protection Circuitry
Over-Voltage Protection
An over-voltage event is defined as a condition
where the voltage on the BAT pin exceeds the
maximum battery charge voltage and is set by the
over-voltage protection threshold (V
OVP
). If an
over-voltage condition occurs, the AAT3685 charge
control will shut down the device until voltage on
the BAT pin drops below the over-voltage protec-
tion threshold (V
OVP
). The AAT3685 will resume
normal charging operation after the over-voltage
condition is removed. During an over-voltage
event, the STAT LEDs will report a system fault; the
actual fault condition may also be read via the
DATA pin signal.
Over-Temperature Shutdown
The AAT3685 has a thermal protection control cir-
cuit which will shut down charging functions should
the internal die temperature exceed the preset
thermal limit threshold.
Battery Temperature Fault Monitoring
In the event of a battery over-temperature condi-
tion, the charge control will turn off the internal pass
device and report a battery temperature fault on the
DATA pin function. The STAT LEDs will also dis-
play a system fault. After the system recovers
from a temperature fault, the device will resume
charging operation.
The AAT3685 checks battery temperature before
starting the charge cycle, as well as during all stages
of charging. This is accomplished by monitoring the
voltage at the TS pin. This system is intended for
use negative temperature coefficient (NTC) thermis-
tors which are typically integrated into the battery
package. Most commonly used NTC thermistors
used in battery packs are approximately 10k
Ω
at
room temperature (25°C). The TS pin has been
specifically designed to source 80
μ
A of current to
the thermistor. The voltage on the TS pin that results
from the resistive load should stay within a window
from 335mV to 2.32V. If the battery becomes too hot
during charging due to an internal fault, the thermis-
tor will heat up and reduce in value, thus pulling the
TS pin voltage lower than the TS1 threshold, and the
AAT3685 will halt charging and signal the fault con-
dition. If the use of the TS pin function is not
required by the system, it should be terminated to
ground using a 10k
Ω
resistor. Alternatively, on the
AAT3685-1, the TS pin may be left open.
Battery Charge Status Indication
The AAT3685 indicates the status of the battery
under charge with two different systems. First, the
device has two status LED driver outputs. These
two LEDs can indicate simple functions such as no
battery charge activity, battery charging, charge
complete, and charge fault. The AAT3685 also
provides a bi-directional data reporting function so
that a system microcontroller may interrogate the
DATA pin and read any one of 14 system states.
Status Indicator Display
Simple system charging status may be displayed
using one or two LEDs in conjunction with the
STAT1 and STAT2 pins on the AAT3685. These
two pins are simple switches to connect the display
LED cathodes to ground. It is not necessary to use
both display LEDs if a user simply wants to have a
single lamp to show "charging" or "not charging."
This can be accomplished by just using the STAT1
pin and a single LED. Using two LEDs and both
STAT pins simply gives the user more information
for charging states. Refer to Table 2 for LED dis-
play definitions.
R
SET
(k
Ω
Ω
)
I
F
10
100
1000
10000
1
10
100
1000
SETL
SETH
AAT3685
Lithium-Ion/Polymer Battery Charger
3685.2006.10.1.3
15
相關PDF資料
PDF描述
AAT3686 USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger
AAT3686IRN-4.2-T1 USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger
AAT3686IXN-4.2-1-T1 USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger
AAT3686IXN-4.2-T1 USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger
AAT3687 Lithium-Ion/Polymer Battery Charger
相關代理商/技術參數
參數描述
AAT3686IXN-4.2-1-T1 制造商:Skyworks Solutions Inc 功能描述:AAT3686 Series 5.5 V USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger
AAT3686IXN-4.2-T1 功能描述:電池管理 USB Port/Adapter/ Polymer Battery Chrg RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel
AAT3687IWP-4.2-1-T1 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC
AAT3687IWP-4.2-T1 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC
AAT3688AIWP-4.2-DB1 制造商:Skyworks Solutions Inc 功能描述:AAT3688 Series USB Port Lithium-Ion/Polymer Battery Charger Evaluation Board
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*