- 您現在的位置：買賣IC網 > PDF目錄381237 > AAT3685IWP-4.2-1-T1 (Advanced Analog Technology,lnc.) Lithium-Ion/Polymer Battery Charger PDF資料下載
參數資料
| 型號： | AAT3685IWP-4.2-1-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Lithium-Ion/Polymer Battery Charger |
| 中文描述： | 鋰離子電池充電器 |
| 文件頁數： | 16/23頁 |
| 文件大小： | 557K |
| 代理商： | AAT3685IWP-4.2-1-T1 |
The LED anodes should be connected to V
ADP/USB
.
The LEDs should be biased with as little current as
necessary to create reasonable illumination; there-
fore, a ballast resistor should be placed between
each of the LED cathodes and the STAT1/2 pins.
LED current consumption will add to the over-ther-
mal power budget for the device package, hence it
is recommended to keep the LED drive current to a
minimum. 2mA should be sufficient to drive most
low-cost green, red, or multi-color LEDs. It is not
recommended to exceed 8mA for driving an indi-
vidual status LED.
The required ballast resistor value can be estimat-
ed using the following formulas:
Eq. 2:
Example:
Note: Red LED forward voltage (V
F
) is typically
2.0V @ 2mA.
Table 2 shows the four status LED display conditions.
Digital Charge Status Reporting
The AAT3685 has a comprehensive digital data
reporting system by use of the DATA pin feature.
This function can provide detailed information
regarding the state of the charging system. The
DATA pin is a bi-directional port which will read
back a series of data pulses when the system
microcontroller asserts a request pulse. This sin-
gle strobe request protocol will invoke one of 14
possible return pulse counts in which the micro-
controller can look up based on the serial report
shown in Table 3.
The DATApin function is active low and should nor-
mally be pulled high to V
ADP/USB
. This data line
may also be pulled high to the same level as the
high state for the logic I/O port on the system
microcontroller. In order for the DATA pin control
circuit to generate clean sharp edges for the data
output and to maintain the integrity of the data tim-
ing for the system, the pull-up resistor on the data
line should be low enough in value so that the
DATA signal returns to the high state without delay.
If the value of the pull-up resistor used is too high,
the strobe pulse from the system microcontroller
may exceed the maximum pulse time and the
DATA output control could issue false status
reports. A 1.5k
Ω
resistor is recommended when
pulling the DATA pin high to 5.0V at the V
USB
input.
If the data line is pulled high to a voltage level less
than 5.0V, the pull-up resistor may be calculated
based on a recommended minimum pull-up current
of 3mA. Use the following formula:
Eq. 3:
V
PULL-UP
3mA
R
PULL-UP
≤
(5.0V
- 2.0
V)
2mA
R
B(STAT1)
=
= 1.5k
Ω
(V
APD/USB
-
V
F(LED)
)
I
LED(STAT1/2)
R
B(STAT1/2)
=
AAT3685
Lithium-Ion/Polymer Battery Charger
16
3685.2006.10.1.3
Table 2: LED Display Status Conditions.
Event Description
STAT1
STAT2
Charge Disabled or Low Supply
Charge Enabled Without Battery
Battery Charging
Charge Completed
Fault
Off
Off
Flash
1
On
Off
On
Flash
1
Off
On
On
1. Flashing rate depends on output capacitance.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3685IWP-4.2-T1 | Lithium-Ion/Polymer Battery Charger |
| AAT3686 | USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3686IRN-4.2-T1 | USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3686IXN-4.2-1-T1 | USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3686IXN-4.2-T1 | USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT3686IXN-4.2-1-T1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3686 Series 5.5 V USB Port/AC Adapter Lithium-Ion/Polymer Battery Charger |
| AAT3686IXN-4.2-T1 | 功能描述:電池管理 USB Port/Adapter/ Polymer Battery Chrg RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| AAT3687IWP-4.2-1-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3687IWP-4.2-T1 | 制造商:Skyworks Solutions Inc 功能描述:POWER MANAGEMENT IC |
| AAT3688AIWP-4.2-DB1 | 制造商:Skyworks Solutions Inc 功能描述:AAT3688 Series USB Port Lithium-Ion/Polymer Battery Charger Evaluation Board |
發布緊急采購，3分鐘左右您將得到回復。