參數資料
型號： AAT3171
廠商： Advanced Analog Technology,lnc.
英文描述： High Current, High Efficiency Charge Pump with Auto-Timer
中文描述： 大電流，高效率電荷泵與自動定時器
文件頁數： 10/19頁
文件大?。?/td> 382K
代理商： AAT3171
AAT3171
High Current, High Efficiency
Charge Pump with Auto-Timer
10
3171.2007.03.1.1
Application Information
Selecting a Timer Capacitor for CT
The CT pin must be configured according to the
desired flash function. There are two options: con-
nect a small valued capacitor or connect the pin to
GND.
Configure the timer feature for the AAT3171 by
connecting a small valued capacitor between the
CT pin and GND. The value of the capacitor will
determine the timeout duration according to the fol-
lowing formula:
As an example, the result of connecting a 0.1μF
capacitor between the CT pin and GND will be a 1
second timeout duration. Operationally, when the
AAT3171 is enabled, it will automatically disable
itself after 1 second. When using the auto-timer
feature, select a CT capacitor value according to
the formula above.
To disable the auto-timer feature, connect the CT
pin to ground. The result will be a small bias current
of approximately 3μA. A large valued pull-down
resistor should not be used for connecting the CT
pin to GND. The CT pin can be connected directly
to GND. If a pull-down resistor is preferred, it
should be of low value (i.e., less than 10K).
The primary considerations for selecting the capac-
itor type are leakage current and tolerance of the
capacitor value. The auto-timer duration is deter-
mined by charging and discharging the timing
capacitor with a small charging/discharging current
of approximately 3μA. Avoid leaky capacitor types
as they will distort the time-out duration. Select the
capacitor value's tolerance according to the
desired time-out tolerance.
Real-Time Control of the CT Pin
To achieve flash and torch mode control, the auto-
timer can be enabled or disabled in real-time. This
can be done by connecting a microcontroller or
microprocessor GPIO port to the CT pin.
To set up flash mode in real-time, enable the auto-
timer by tri-stating the GPIO port. Do not drive the
port high. It can only be set to high-impedance so
that the CT capacitor can be charged and dis-
charged by the AAT3171.
To set up torch mode in real-time, disable the auto-
timer by driving the GPIO port low so that the CT
pin will be pulled to GND through the GPIO port.
Figure 2: Enable or Disable the Auto-Timer in
Real-Time for Flash/Torch Control.
Flash/Torch Control Using the RSET Pin
An alternative method can be used for flash/torch
control that eliminates the need to use the S
2
Cwire
single-wire interface. By using any typical digital
I/O port, an additional enable can be created (see
Figure 3).
The I/O port output configuration can be any one of
open-drain NMOS, open-drain PMOS, or push-pull
type. The control will always act as an active-low
flash enable or, equivalently, an active-high torch
enable (see Table 2).
AAT3171
EN/SET
CT
Tri-state = TMR ON
Low = TMR OFF
0.1μF = 1 sec
T = C
T
· 10μF
相關PDF資料
PDF描述
AAT3171IWP-T1 High Current, High Efficiency Charge Pump with Auto-Timer
AAT3216IGV-3.0-T1 150mA MicroPower⑩ LDO with PowerOK
AAT3216 150mA MicroPower⑩ LDO with PowerOK
AAT3216IGV-1.2-T1 150mA MicroPower⑩ LDO with PowerOK
AAT3216IGV-1.5-T1 150mA MicroPower⑩ LDO with PowerOK
相關代理商/技術參數
參數描述
AAT3171AIWP-T1 制造商:SKYWORKS SOLUTIONS INC 功能描述:800MA FLASH DRIVER CHPUMP 12TDFN TR
AAT3171IWP-T1 制造商:Skyworks Solutions Inc 功能描述:Voltage Regulators - Switching Regulators Hi Cur Hi Efficiency Charge Pump w/ Timer
AAT3172 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Current LED Flash Driver Charge Pump IC
AAT3172_08 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:High Current LED Flash Driver Charge Pump IC
AAT3172IWP-T1 制造商:SKYWORKS SOLUTIONS INC 功能描述:600 MA FLASH DRIVER CHPMP 12TDFN TR 制造商:Skyworks Solutions Inc 功能描述:LED DRIVER IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*