- 您現在的位置：買賣IC網 > PDF目錄381233 > AAT2803ISK-4.5-T1 (Advanced Analog Technology,lnc.) Six-Channel White LED Backlight Charge Pump with Flash PDF資料下載
參數資料
| 型號： | AAT2803ISK-4.5-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | Six-Channel White LED Backlight Charge Pump with Flash |
| 中文描述： | 六通道白光LED閃光背光電荷泵 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 589K |
| 代理商： | AAT2803ISK-4.5-T1 |
AAT2803
Six-Channel White LED Backlight
Charge Pump with Flash
2803.2006.12.1.6
11
Functional Block Diagram
1X
1.5X
2X
Charge
Pump
Soft-Start
Control
1MHz
Oscillator
Voltage
Reference
C2
+
C2
-
C3
+
C3
-
V
OUT_BL
EN/SET
V
IN
V
OUT_FL
V
REF
Soft-Start
1MHz
Oscillator
2X
Charge Pump
C1
+
C1
-
EN_FL
D/A
D/A
D/A
D/A
D/A
D/A
6 x 16 bit
ROM
6 x 16 bit
ROM
AS
2
Cwire
Interface
D6
GND
D5
D4
D3
D2
D1
Functional Description
The AAT2803 is a dual charge pump targeted for
backlight and flash applications. The charge pump
for white LED applications is a tri-mode load switch
(1X) and high efficiency (1.5X or 2X) charge pump
device. To maximize power conversion efficiency,
an internal sensing circuit monitors the voltage
required on each constant current sink input and
sets the load switch and charge pump modes based
on the input battery voltage and the current sink
input voltage. As the battery discharges over time,
the backlight charge pump is enabled when any of
the six current sink inputs near dropout. The charge
pump initially starts in 1.5X mode. If the charge
pump output drops enough for any current source
output to become close to dropout, the charge pump
will automatically transition to 2X mode.
For flash applications, charge pump doubler archi-
tecture is used to support the high current demand
required by the application. Charge pump regula-
tion is achieved by sensing the output voltage
through an internal resistor divider network. A
switch doubling circuit is enabled when the divided
output drops below a preset trip point controlled by
an internal comparator. The free-running charge
pump switching frequency is approximately 1MHz.
The charge pump is designed to deliver 120mA of
continuous current and 300mA of pulsed current.
The AAT2803 requires only six external compo-
nents: three 1
μ
F ceramic capacitors for the charge
pump flying capacitors (C
1
, C
2
, and C
3
), one 1
μ
F
ceramic input capacitor (C
IN
), one 0.33
μ
F to 1
μ
F
ceramic capacitor for the backlight charge pump
output, and one 1
μ
F for the flash charge pump out-
put. The six constant current sink inputs (D1 to D6)
can drive six individual LEDs with a maximum cur-
rent of 30mA each. The unused sink inputs must be
connected to V
OUT_BL
, otherwise the part will operate
only in 2X charge pump mode. The AS
2
Cwire serial
interface enables the backlight charge pump and
sets the current sink magnitudes. AS
2
Cwire
addressing allows independent control of two
groups of current sink input: D1 to D4 and D5 to D6.
相關PDF資料 |
PDF描述 |
|---|---|
| AAT3110IGU-4.5-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3110IGU-5.0-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3110IJS-4.5-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3110IJS-5.0-T1 | MicroPower⑩ Regulated Charge Pump |
| AAT3111IGU-3.3-T1 | MicroPower⑩ Regulated Charge Pump |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT2805 | 制造商:AAT 制造商全稱:AAT 功能描述:Dual High Efficiency Charge Pump for White LED and Flash Applications |
| AAT2805IXN-4.5-T1 | 制造商:AAT 制造商全稱:AAT 功能描述:Dual High Efficiency Charge Pump for White LED and Flash Applications |
| AAT2806 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Dual High Efficiency Charge Pump for White LED and Flash Applications |
| AAT2806_07 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Dual High Efficiency Charge Pump for White LED and Flash Applications |
| AAT2806IXN-4.5-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:Dual High Efficiency Charge Pump for White LED AND Flash Applications |
發布緊急采購，3分鐘左右您將得到回復。