- 您現在的位置：買賣IC網 > PDF目錄381232 > AAT1149IJS-0.6-T1 (Advanced Analog Technology,lnc.) 3MHz Fast Transient 400mA Step-Down Converter PDF資料下載
參數資料
| 型號： | AAT1149IJS-0.6-T1 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | 3MHz Fast Transient 400mA Step-Down Converter |
| 中文描述： | 3MHz的快速瞬態400mA的降壓轉換器 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 1800K |
| 代理商： | AAT1149IJS-0.6-T1 |
AAT1149
3MHz Fast Transient
400mA Step-Down Converter
1149.2006.11.1.0
11
Control Loop
The AAT1149 is a peak current mode step-down
converter. The current through the P-channel
MOSFET (high side) is sensed for current loop
control, as well as short circuit and overload pro-
tection. A fixed slope compensation signal is added
to the sensed current to maintain stability for duty
cycles greater than 50%. The peak current mode
loop appears as a voltage-programmed current
source in parallel with the output capacitor.
The output of the voltage error amplifier programs
the current mode loop for the necessary peak
switch current to force a constant output voltage for
all load and line conditions. Internal loop compen-
sation terminates the transconductance voltage
error amplifier output. For the adjustable output,
the error amplifier reference is fixed at 0.6V.
Soft Start / Enable
Soft start limits the current surge seen at the input
and eliminates output voltage overshoot. When
pulled low, the enable input forces the AAT1149
into a low-power, non-switching state. The total
input current during shutdown is less than 1
μ
A.
Current Limit and Over-Temperature
Protection
For overload conditions, the peak input current is
limited. To minimize power dissipation and stresses
under current limit and short-circuit conditions,
switching is terminated after entering current limit
for a series of pulses. Switching is terminated for
seven consecutive clock cycles after a current limit
has been sensed for a series of four consecutive
clock cycles.
Thermal protection completely disables switching
when internal dissipation becomes excessive. The
junction over-temperature threshold is 140°C with
15°C of hysteresis. Once an over-temperature or
over-current fault conditions is removed, the output
voltage automatically recovers.
Under-Voltage Lockout
Internal bias of all circuits is controlled via the IN
input. Under-voltage lockout (UVLO) guarantees
sufficient V
IN
bias and proper operation of all inter-
nal circuitry prior to activation.
Applications Information
Inductor Selection
The step-down converter uses peak current mode
control with slope compensation to maintain stability
for duty cycles greater than 50%. The output induc-
tor value must be selected so the inductor current
down slope meets the internal slope compensation
requirements.
Table 1 displays suggested inductor
values for various output voltages.
Manufacturer's specifications list both the inductor
DC current rating, which is a thermal limitation, and
the peak current rating, which is determined by the
saturation characteristics. The inductor should not
show any appreciable saturation under normal load
conditions. Some inductors may meet the peak and
average current ratings yet result in excessive loss-
es due to a high DCR. Always consider the losses
associated with the DCR and its effect on the total
converter efficiency when selecting an inductor.
The 1.8
μ
H CDRH2D09 series inductor selected
from Sumida has a 131m
Ω
DCR and a 400mA sat-
uration current rating. At full load, the inductor DC
loss is 21mW which gives a 2.8% loss in efficiency
for a 400mA, 1.8V output.
Input Capacitor
Select a 4.7
μ
F to 10
μ
F X7R or X5R ceramic capac-
itor for the input. To estimate the required input
capacitor size, determine the acceptable input rip-
ple level (V
PP
) and solve for C. The calculated
value varies with input voltage and is a maximum
when V
IN
is double the output voltage.
C
IN(MIN)
=
1
- ESR
·
4
·
F
S
I
O
V
PP
· 1
-
= 1
IN
= 2 · V
O
V
IN
V
IN
V
O
4
· 1
-
V
O
V
IN
C
IN
=
V
O
V
IN
- ESR
·
F
S
V
PP
I
O
相關PDF資料 |
PDF描述 |
|---|---|
| AAT1149 | 3MHz Fast Transient 400mA Step-Down Converter |
| AAT1151 | 850kHz 700mA Synchronous Buck DC/DC Converter |
| AAT1151_07 | 850kHz 700mA Synchronous Buck DC/DC Converter |
| AAT1151IKS-1.0-T1 | 850kHz 700mA Synchronous Buck DC/DC Converter |
| AAT1151IKS-1.8-T1 | 850kHz 700mA Synchronous Buck DC/DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT1149IUV-0.6-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:3MHz Fast Transient 400mA Step-Down Converter |
| AAT1150 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:1MHz 1A Step-Down DC/DC Converter |
| AAT1150_06 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:1MHz 1A Step-Down DC/DC Converter |
| AAT1150IKS-1.0-T1 | 制造商:Skyworks Solutions Inc 功能描述:SKYAAT1150IKS-1.0-T1 DC/DC CONVERTERS (S 制造商:SKYWORKS SOLUTIONS 功能描述:AAT1150 Series 5.5 V 1 MHz 1 A Synchronous Buck DC/DC Converter - MSOP-8 制造商:Skyworks Solutions Inc 功能描述:DC TO DC CONVERTER |
| AAT1150IKS-1.5-T1 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:1MHz 1A Step-Down DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。