- 您現在的位置：買賣IC網 > PDF目錄362041 > AA2820 Controller Miscellaneous - Datasheet Reference PDF資料下載
參數資料
| 型號： | AA2820 |
| 英文描述： | Controller Miscellaneous - Datasheet Reference |
| 中文描述： | 控制器雜項-數據表參考 |
| 文件頁數： | 3/7頁 |
| 文件大?。?/td> | 296K |
| 代理商： | AA2820 |
(VOLTS)
(VOLTS)
(VOLTS)
3
4
Figure 3: Input/Output Waveform Characteristics
TYPICAL OUTPUT CHARACTERISTICS
Figure 4: High Voltage Output (OUT5) vs. Reset
(R13) and OUT1.
BILEVEL DRIVE
The basic function of a step motor driver is to control the motor winding
currents. Motor performance is determined by how fast the driver can
increase and decrease the winding currents. A rapid rise in winding current is
achieved by applying a high voltage directly to a motor. This rapid rise of
current is also referred to as the "kick" or operating current. When a desired
current level is reached, a low voltage is applied to maintain a suitable holding
current level. When a motor winding is turned off, a rapid decrease in winding
current is achieved by routing the energy in the collapsing field back to the
power supply through a high voltage path. The high voltage supply furnishes
the energy necessary to maintain motor output torque at high step rates thus
providing high mechanical power output. The low voltage supply provides
much of the current needed at low step rates and all of the holding current.
The efficiency of bilevel drive makes for step motor performance that is far
superior to that produced by L/R drives. Also, bilevel drivers do not use high
frequency switching techniques as chopper drivers do. Consequently, they do
not create the EMI, RFI, and motor heating problems that are associated with
chopper drivers.
AA2020 Operation
Each time the chip receives a clock signal, the phase outputs change state.
When a phase output turns on, a high voltage output also turns on. This high
voltage output is used to turn on a high-side switch. The high voltage output
will stay on until the chip gets a reset signal. In Figure 4, OUT1 turns on when
the CLOCK input goes low. OUT5 turns on at the same time. OUT5 stays on
until the reset input, R13 goes low. The waveforms in Figure 4 are for half-
step operation. In half-step operation, the phase outputs are on for three clock
cycles. The high voltage output will turn on the first two of these cycles. If the
reset input never goes low, the high voltage output will stay on. In full-step
operation, each phase output is on for two clock cycles and the corresponding
high voltage output will turn on at the beginning of each clock cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| AA20C-048L-0335-M1 | Analog IC |
| AA20C-048L-050S | Analog IC |
| AA20C-048L-050S1 | Analog IC |
| AA20C-048L-050S4 | Analog IC |
| AA20C-048L-050S9 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AA28600001 | 功能描述:28.63636MHz ±20ppm 晶體 20pF -40°C ~ 85°C 表面貼裝 2-SMD 制造商:txc corporation 系列:AA 包裝:* 零件狀態:有效 類型:MHz 晶體 頻率:28.63636MHz 頻率穩定度:±30ppm 頻率容差:±20ppm 負載電容:20pF ESR（等效串聯電阻）:- 工作模式:- 工作溫度:-40°C ~ 85°C 等級:- 安裝類型:表面貼裝 封裝/外殼:2-SMD 大小/尺寸:0.197" 長 x 0.126" 寬（5.00mm x 3.20mm） 高度:0.053"（1.35mm） 標準包裝:1,000 |
| AA-293-08XT | 制造商:Molex 功能描述: |
| AA2-A0-03-630-1B1-C | 制造商:Carling Technologies 功能描述:A-SERIES CIRCUIT BREAKER - Bulk |
| AA2-A1-03-630-1B1-C | 制造商:Carling Technologies 功能描述:A-SERIES CIRCUIT BREAKER - Bulk |
| AA2-A3-03-630-1D2-C | 制造商:Carling Technologies 功能描述:A-SERIES CIRCUIT BREAKER - Bulk |
發布緊急采購，3分鐘左右您將得到回復。