- 您現在的位置：買賣IC網 > PDF目錄375160 > A8902 (Allegro MicroSystems, Inc.) Three-Phase Brushless DC Motor Controller/ Driver(用于5V或12V硬盤驅動器的三相無刷直流電機控制器/驅動器) PDF資料下載
參數資料
| 型號： | A8902 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Three-Phase Brushless DC Motor Controller/ Driver(用于5V或12V硬盤驅動器的三相無刷直流電機控制器/驅動器) |
| 中文描述： | 三相無刷直流電動機控制器/驅動器（用于5V的或12V的硬盤驅動器的三相無刷直流電機控制器/驅動器） |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 156K |
| 代理商： | A8902 |
8902–A
3-PHASE BRUSHLESS DC
MOTOR CONTROLLER/DRIVER
Serial Port.
The serial port functions to write various operational
and diagnostic modes to the A8902CLBA. The serial port DATA IN is
enabled/disabled by the CHIP SELECT terminal. When CHIP SE-
LECT is high the serial port is disabled and the chip is not affected by
changes in data at the DATA IN or CLOCK terminals.
To write data to the serial port, the CLOCK terminal should be low
prior to the CHIP SELECT terminal going low. Once CHIP SELECT
goes low, information on the DATA IN terminal is read into the shift
register on the positive-going transition of the CLOCK. There are 24
bits in the serial input port.
Data written into the serial port is latched and becomes active
upon the low-to-high transition of the CHIP SELECT terminal at the
end of the write cycle. D0 will be the last bit written to the serial port.
SERIAL PORT BIT DEFINITIONS
D0- Sleep/Run Mode; LOW = Sleep, HIGH = Run
This bit allows the device to be powered down when not in use.
D1- Step Mode; LOW = Normal Operation, HIGH = Step Only
When in the step-only mode the back-EMF commutation circuitry
is disabled and the power outputs are commutated by the start-
up oscillator. This mode is intended for device and system
testing.
D2- Brake; LOW = Run, HIGH = Brake.
D3 and D4 - These two bits set the output current limit:
D3
D4
Current Limit
0
0
1
1
0
1
0
1
1.2 A
1 A
600 mA
250 mA
D5 thru D18-This 14-bit word (active low) programs the
REF
time to set
desired motor speed.
Bit Number Count Number
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
16
32
64
128
256
512
1 024
2 048
4 096
8 192
16 384
32 768
65 536
131 072
D19-Speed-control mode switch;
LOW = internal once-around speed signal,
HIGH = external sector data.
D20 and D21-These bits program the number
of motor poles for the once-around
FCOM
counter:
D20
D21
Motor Poles
0
0
1
1
0
1
0
1
8
–
16
12
D22 and D23-Controls the multiplexer for
DATA OUT:
D22
D23
DATA OUT
0
0
1
1
0
1
0
1
TACH (once around or sector)
Thermal Shutdown
SYNC
FCOM
Reset.
The RESET terminal when pulled
low clears all serial port bits, including the D0
latch, which puts the A8902CLBA in the sleep
mode.
相關PDF資料 |
PDF描述 |
|---|---|
| A8904SLB | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| A8904SLB-T | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| A8904SLP | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| A8904SLP-T | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
| A8904 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A8902CLBA | 制造商:Allegro MicroSystems LLC 功能描述:DC Motor Driver 24-Pin SOIC(300mil) |
| A8902CLBAJ | 制造商:Allegro MicroSystems LLC 功能描述:2CLBAJ |
| A8902SLB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| A8903SLB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| A8904 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER WITH BACK-EMF SENSING |
發布緊急采購，3分鐘左右您將得到回復。