SX Family FPGAs
1- 24
v3.2
A54SX08 Timing Characteristics
Table 1-17 A54SX08 Timing Characteristics
(Worst-Case Commercial Conditions, VCCR = 4.75 V, VCCA,VCCI = 3.0 V, TJ = 70°C)
Parameter
Description
'–3' Speed
'–2' Speed
'–1' Speed
'Std' Speed
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Units
C-Cell Propagation Delays1
tPD
Internal Array Module
0.6
0.7
0.8
0.9
ns
Predicted Routing Delays2
tDC
FO = 1 Routing Delay, Direct Connect
0.1
ns
tFC
FO = 1 Routing Delay, Fast Connect
0.3
0.4
0.5
ns
tRD1
FO = 1 Routing Delay
0.3
0.4
0.5
ns
tRD2
FO = 2 Routing Delay
0.6
0.7
0.8
0.9
ns
tRD3
FO = 3 Routing Delay
0.8
0.9
1.0
1.2
ns
tRD4
FO = 4 Routing Delay
1.0
1.2
1.4
1.6
ns
tRD8
FO = 8 Routing Delay
1.9
2.2
2.5
2.9
ns
tRD12
FO = 12 Routing Delay
2.8
3.2
3.7
4.3
ns
R-Cell Timing
tRCO
Sequential Clock-to-Q
0.8
1.1
1.2
1.4
ns
tCLR
Asynchronous Clear-to-Q
0.5
0.6
0.7
0.8
ns
tPRESET
Asynchronous Preset-to-Q
0.7
0.8
0.9
1.0
ns
tSUD
Flip-Flop Data Input Set-Up
0.5
0.7
0.8
ns
tHD
Flip-Flop Data Input Hold
0.0
ns
tWASYN
Asynchronous Pulse Width
1.4
1.6
1.8
2.1
ns
Input Module Propagation Delays
tINYH
Input Data Pad-to-Y HIGH
1.5
1.7
1.9
2.2
ns
tINYL
Input Data Pad-to-Y LOW
1.5
1.7
1.9
2.2
ns
Input Module Predicted Routing Delays2
tIRD1
FO = 1 Routing Delay
0.3
0.4
0.5
ns
tIRD2
FO = 2 Routing Delay
0.6
0.7
0.8
0.9
ns
tIRD3
FO = 3 Routing Delay
0.8
0.9
1.0
1.2
ns
tIRD4
FO = 4 Routing Delay
1.0
1.2
1.4
1.6
ns
tIRD8
FO = 8 Routing Delay
1.9
2.2
2.5
2.9
ns
tIRD12
FO = 12 Routing Delay
2.8
3.2
3.7
4.3
ns
Note:
1. For dual-module macros, use tPD + tRD1 + tPDn, tRCO + tRD1 + tPDn, or tPD1 + tRD1 + tSUD, whichever is appropriate.
2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating
device performance. Post-route timing analysis or simulation is required to determine actual worst-case performance. Post-route
timing is based on actual routing delay measurements performed on the device prior to shipment.