- 您現在的位置：買賣IC網 > PDF目錄379523 > A42MX09-FBG100ES (Electronic Theatre Controls, Inc.) 40MX and 42MX FPGA Families PDF資料下載
參數資料
| 型號： | A42MX09-FBG100ES |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 40MX and 42MX FPGA Families |
| 中文描述： | 40MX和42MX FPGA系列 |
| 文件頁數： | 36/123頁 |
| 文件大?。?/td> | 854K |
| 代理商： | A42MX09-FBG100ES |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
40MX and 42MX FPGA Families
1-30
v6.0
Predictable Performance: Tight Delay Distributions
Propagation delay between logic modules depends on
the resistive and capacitive loading of the routing tracks,
the interconnect elements, and the module inputs being
driven. Propagation delay increases as the length of
routing tracks, the number of interconnect elements, or
the number of inputs increases.
From a design perspective, the propagation delay can be
statistically correlated or modeled by the fanout
(number of loads) driven by a module. Higher fanout
usually requires some paths to have longer routing
tracks.
The MX FPGAs deliver a tight fanout delay distribution,
which is achieved in two ways: by decreasing the delay of
the interconnect elements and by decreasing the number
of interconnect elements per path.
Actel’s patented antifuse offers a very low resistive/
capacitive interconnect. The antifuses, fabricated in
0.45 μm lithography, offer nominal levels of 100
resistance and 7.0fF capacitance per antifuse.
MX fanout distribution is also tight due to the low
number of antifuses required for each interconnect path.
The proprietary architecture limits the number of
antifuses per path to a maximum of four, with
90 percent of interconnects using only two antifuses.
Timing Characteristics
Device timing characteristics fall into three categories:
family-dependent,
device-dependent,
dependent. The input and output buffer characteristics
are common to all MX devices. Internal routing delays
are device-dependent; actual delays are not determined
until after place-and-route of the user's design is
complete. Delay values may then be determined by using
the Designer software utility or by performing
simulation with post-layout delays.
and
design-
Critical Nets and Typical Nets
Propagation delays are expressed only for typical nets,
which are used for initial design performance evaluation.
Critical net delays can then be applied to the most timing
critical paths. Critical nets are determined by net
property assignment in Actel's Designer software prior to
placement and routing. Up to 6% of the nets in a design
may be designated as critical.
Long Tracks
Some nets in the design use long tracks, which are
special routing resources that span multiple rows,
columns, or modules. Long tracks employ three and
sometimes four antifuse connections, which increase
capacitance and resistance, resulting in longer net delays
for macros connected to long tracks. Typically, up to
6 percent of nets in a fully utilized device require long
tracks. Long tracks add approximately a 3 ns to a 6 ns
delay, which is represented statistically in higher fanout
(FO=8) routing delays in the data sheet specifications
section, shown in
Table 28 on page 1-36
.
Timing Derating
MX devices are manufactured with a CMOS process.
Therefore, device performance varies according to
temperature, voltage, and process changes. Minimum
timing parameters reflect maximum operating voltage,
minimum
operating
temperature
processing.
Maximum
timing
minimum operating voltage, maximum operating
temperature and worst-case processing.
and
best-case
reflect
parameters
相關PDF資料 |
PDF描述 |
|---|---|
| A42MX09-FBG100I | 40MX and 42MX FPGA Families |
| A42MX09-FBG100M | 40MX and 42MX FPGA Families |
| A42MX09-FCQ100 | 40MX and 42MX FPGA Families |
| A42MX09-FCQ100A | 40MX and 42MX FPGA Families |
| A42MX09-FCQ100B | 40MX and 42MX FPGA Families |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A42MX09-FBG100I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families |
| A42MX09-FBG100M | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:40MX and 42MX FPGA Families |
| A42MX09-FCQ100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families |
| A42MX09-FCQ100A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families |
| A42MX09-FCQ100B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:40MX and 42MX FPGA Families |
發布緊急采購，3分鐘左右您將得到回復。