參數資料
型號: A40MX04-PL84I
英文描述: Field Programmable Gate Array (FPGA)
中文描述: 現場可編程門陣列(FPGA)
文件頁數: 11/116頁
文件大小: 3110K
代理商: A40MX04-PL84I
v5.0
11
40MX and 42MX FPGA Families
When a device is operating in BST mode, four I/O pins are
used for the TDI, TDO, TMS, and TCK signals. An active
reset (nTRST) pin is not supported; however, the 42MX
device contain power-on circuitry that resets the boundary
scan circuitry upon power-up.
Table 1
summarizes the
functions of the IEEE 1149.1 BST signals.
JTAG
All SX-A devices are IEEE 1149.1 (JTAG) compliant. SX-A
devices offer superior diagnostic and testing capabilities by
providing JTAG and probing capabilites. These functions
are controlled through the special JTAG pins in conjunction
with the program fuse.
JTAG fuse programmed:
TCK must be terminated
logical high or low doesn
t
matter (to avoid floating input)
TDI, TMS may float or at logical high (internal pull-up is
present)
TDO may float or connect to TDI of another device (it
s an
output)
JTAG fuse not programmed:
TCK, TDI, TDO, TMS are user I/O. If not used, they will be
configured as tristated output.
BST Instructions
Boundary scan testing within the 42MX devices is controlled
by a Test Access Port (TAP) state machine. The TAP
controller drives the three-bit instruction register, a bypass
register, and the boundary scan data registers within the
device. The TAP controller uses the TMS signal to control
the testing of the device. The BST mode is determined by
the bitstream entered on the TMS pin.
Table 2
describes the
test instructions supported by the 42MX devices.
Reset
The TMS pin is equipped with an internal pull-up resistor.
This allows the TAP controller to remain in or return to the
Test-Logic-Reset state when there is no input or when a
logical 1 is on the TMS pin. To reset the controller, TMS
must be HIGH for at least five TCK cycles.
Figure 11
42MX IEEE 1149.1 Boundary Scan Circuitry
JPROBE Register
Boundary Scan Register
Instruction
Decode
Control Logic
TAP Controller
Instruction
Register
Bypass
Register
TMS
TCK
TDI
Output
MUX
TDO
JTAG
JTAG
Table 1
IEEE 1149.1 BST Signals
Signal
Name
Function
TDI
Test Data In
Serial data input for BST
instructions and data. Data is
shifted in on the rising edge of
TCK.
TDO
Test Data
Out
Serial data output for BST
instructions and test data.
TMS
Test Mode
Select
Serial data input for BST mode.
Data is shifted in on the rising
edge of TCK.
TCK
Test Clock
Clock signal to shift the BST
data into the device.
相關PDF資料
PDF描述
A40MX04-PL84M Field Programmable Gate Array (FPGA)
A40MX04-PQ100 Field Programmable Gate Array (FPGA)
A40MX04-PQ100I Field Programmable Gate Array (FPGA)
A40MX04-PQ100M Field Programmable Gate Array (FPGA)
A40MX04-VQ80 Field Programmable Gate Array (FPGA)
相關代理商/技術參數
參數描述
A40MX04-PL84M 制造商:Microsemi Corporation 功能描述:FPGA 6K GATES 547 CELLS 83MHZ/139MHZ 0.45UM 3.3V/5V 84PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:IC FPGA 69 I/O 84PLCC 制造商:Microsemi Corporation 功能描述:IC FPGA MX SGL CHIP 6K 84-PLCC
A40MX04-PLG44 功能描述:IC FPGA 69I/O 44PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:MX 標準包裝:24 系列:ECP2 LAB/CLB數:1500 邏輯元件/單元數:12000 RAM 位總計:226304 輸入/輸出數:131 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP(28x28)
A40MX04-PLG44I 功能描述:IC FPGA MX SGL CHIP 6K 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:MX 標準包裝:90 系列:ProASIC3 LAB/CLB數:- 邏輯元件/單元數:- RAM 位總計:36864 輸入/輸出數:157 門數:250000 電源電壓:1.425 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 125°C 封裝/外殼:256-LBGA 供應商設備封裝:256-FPBGA(17x17)
A40MX04-PLG44M 制造商:Microsemi Corporation 功能描述:FPGA 6K GATES 547 CELLS 83MHZ/139MHZ 0.45UM 3.3V/5V 44PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:IC FPGA 34 I/O 44PLCC
A40MX04-PLG68 功能描述:IC FPGA 69I/O 68PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:MX 標準包裝:24 系列:ECP2 LAB/CLB數:1500 邏輯元件/單元數:12000 RAM 位總計:226304 輸入/輸出數:131 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP(28x28)