- 您現在的位置：買賣IC網 > PDF目錄210083 > A3CJ-90B1-12EG PUSHBUTTON SWITCH, SPDT, ALTERNATE, 1A, 30VDC, PANEL MOUNT-THREADED PDF資料下載
參數資料
| 型號： | A3CJ-90B1-12EG |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, SPDT, ALTERNATE, 1A, 30VDC, PANEL MOUNT-THREADED |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 253K |
| 代理商： | A3CJ-90B1-12EG |
A3C
A3C
46
Precautions
Caution
Do not apply a voltage higher than the maximum rated operat-
ing voltage between the lamp terminals, as there is a risk that
the incandescent lamp or LED lamp will be damaged, and the
Pushbutton will be ejected.
When replacing the incandescent lamp, first turn OFF the
power supply, and then wait 10 minutes before performing re-
placement, as the lamp is still hot immediately after the power
is turned OFF, so there is a risk of burns.
Refer to the Common Precautions for Pushbutton Switches on
page 14.
Correct Use
Mounting
To prevent electric shock or a fire, always make sure that the power
is turned OFF before mounting, removing, or wiring the Switch, or
performing maintenance.
Do not tighten the mounting ring excessively using pliers or a similar
tool. Excessive tightening may damage the mounting ring. (Tighten-
ing torque: 0.20 to 0.39 N
m)
Wiring
When wiring, use wires of a size appropriate for the applied voltage
and carry current. Perform soldering correctly under the conditions
given below. Using the Switch with the wires soldered incorrectly
may cause the terminals to become abnormally hot and cause a fire.
1. Hand soldering: At 30 W within 5 seconds.
2. Dip soldering: At 240
°C within 3 seconds.
Wait for one minute after soldering before exerting any external
force on the solder.
Use a non-corrosive rosin liquid for the flux.
Perform wiring so that the wire sheaths do not come into contact
with the Switch. If this is unavoidable, use wires that can withstand
temperatures of 100
°C min.
After wiring to the Switch has been completed, ensure an appropri-
ate insulation distance.
Operating Environment
Do not use in locations that are subject to dust, oil, or metal filings as
these may penetrate the interior of the Switch and cause malfunc-
tion.
Using Microloads
Using a standard load switch for opening and closing a microload
circuit may cause wear on the contacts. Use the switch within the
operating range. (Refer to the diagram below.) Even when using mi-
croload models within the operating range shown below, if inrush
current occurs when the contact is opened or closed, it may cause
the contact surface to become rough, and so decrease life expec-
tancy. Therefore, insert a contact protection circuit where neces-
sary. The minimum applicable load is the N-level reference value.
This value indicates the malfunction reference level for the reliability
level of 60% (
λ 60) (conforming to JIS C5003). The equation, λ 60 =
0.5 x 10–4/times indicates that the estimated malfunction rate is less
than 1/2,000,000 with a reliability level of 60%.
Standard
load area
Microload
area
Invalid
area
V
oltage
(V)
Current (mA)
0.15 mA
26 mA
100 mA
150 mA
100 mA
1 mA
30
24
12
5
0
LED
Resistance to limit the LED current is provided internally and so an
external resistance is not required.
Rated voltage
Internal limiting resistance
5 VDC
33
12 VDC
270
24 VDC
1600
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. A030-E1-05
!
相關PDF資料 |
PDF描述 |
|---|---|
| A3CT-90B0-B | PUSHBUTTON SWITCH, SPDT, ALTERNATE, 1A, 30VDC, PANEL MOUNT-THREADED |
| A10005MSMCGF | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.35A, 125VDC, THROUGH HOLE-STRAIGHT |
| A10005MSZGE | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.35A, 125VDC, PANEL MOUNT-THREADED |
| A10005RNMCB | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
| A10014MNMCBF | ROTARY SWITCH-12POSITIONS, SP12T, LATCHED, 0.02A, 20VDC, THROUGH HOLE-STRAIGHT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A3CJ90B112EW | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:ASSEMBLED LIGHTED PUSHBUTTON |
| A3CJ-90B1-12EW | 功能描述:按鈕開關 ASSEMBLED LIGHTED PUSHBUTTON RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| A3CJ90B112EWNC | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSHBUTTON SPDT 1A 125V |
| A3CJ90F0A | 制造商:Omron Corporation 功能描述:Switch Push Button N.O./N.C. SPDT Flush Rectangular Button 0.1A 125VAC 30VDC Alternate Contact Solder Panel Mount |
| A3CKA-1006G | 功能描述:IDC CABLE-AKN10A/ AE10G / APK10A RoHS:否 類別:電纜組件 >> 矩形 系列:- 標準包裝:1 系列:- 連接器類型:插頭至插頭 位置數:30 行數:2 間距 - 連接器:0.100"（2.54mm） 間距 - 線纜:0.050"（1.27mm） 長度:1.50'（457.20mm） 特點:電極標記 顏色:多色，帶狀 屏蔽:無屏蔽 使用:- 電纜端接:IDC 觸點表面涂層:金 觸點涂層厚度:30µin（0.76µm） |
發布緊急采購，3分鐘左右您將得到回復。