- 您現在的位置：買賣IC網 > PDF目錄223291 > A22E-SK-11 PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT PDF資料下載
參數資料
| 型號： | A22E-SK-11 |
| 元件分類： | 開關 |
| 英文描述： | PUSHBUTTON SWITCH, SPST, MOMENTARY, 10A, 24VDC, PANEL MOUNT |
| 文件頁數： | 10/20頁 |
| 文件大小： | 2782K |
| 代理商： | A22E-SK-11 |
Emergency Stop Switch
A22E
D-29
A2
2
E
Em
er
ge
nc
y
St
op
S
wit
c
h
es
Safety Precautions
Be sure to read the precautions for all pushbutton switches in the Pushbutton Switches Group Catalog (Cat. No. X018).
!CAUTION
■ Precautions for Correct Use
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance. Electric
shock may occur.
Do not tighten the mounting ring more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting ring.
The tightening torque is 0.98 to 1.96 Nm.
Recommended panel thickness: 1 to 5 mm.
Wiring
When DC-specific LEDs are used, wire the Switch so that the X1
terminal is positive.
Terminal screws must be Phillips or slotted M3.5 screws with a
square washer.
The tightening torque is 1.08 to 1.27 Nm.
Single wires, stranded wires, and crimp terminals can be connected
to the Switch.
Applicable Wiring Materials:
Twisted strands: 2 mm2 max.
Solid wire: 1.6 mm dia.
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Operating Environment
The IP65 model is designed with a protective structure so that it will
not sustain damage if it is subjected to water from any direction to the
front of the panel.
Using the Microload
Contact failure may occur is a Switch designed for a standard load is
used to switch a microload. Use Switches within the application
ranges shown in the following graph. Even within the application
range, insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability level
of 60% (
λ 60) (conforming to JIS C5003).
The equation,
λ 60 = 0.5 x 106/time indicates that the estimated
malfunction rate is less than 1/2,000,000 with a reliability level of 60%.
LEDs
The LED current-limiting resistor is built-in, so internal resistance is
not required.
If commercially available LEDs are used, select the ones that meet
the following conditions:
Base: BA9S/13
@
Overall length: 26 mm max.
Power consumption: 2.6 W max.
Others
The oil-resistant IP65 uses NBR rubber and is resistant to general
cutting oil and cooling oil. Some particular oils cannot be used with
the oil-resistant IP65, however, so contact your OMRON
representative for details.
If the panel is to be finished with coating, etc., make sure that the
panel meets the specified dimensions after the coating.
Do not subject the Switch to extreme shock or vibration. Doing so will
cause malfunctions and damage to the Switch.
Do not let sharp objects come into contact with the Switches that are
made of resin. Doing so will damage the Switches, causing
scratches on the outside of the Pushbuttons, and malfunction.
When handling the Switches, do not throw or drop them.
Do not apply a voltage exceeding the rated voltage across the
incandescent lamp terminals.
The lamp may be destroyed and the operation unit may fly out.
8 mm max.
16.0 mm max.
8 mm dia. max.
16.0 mm max.
Naked Crimp Terminals
20.2 mm max.
8 mm max.
20.2 mm max.
8 mm dia. max.
Crimp Terminals with
Insulating Sheaths
Invalid
area
0.1
1
10
100
1,000
10 mA
1 mA
5
12
24
30
0.16 mA
1.6 mA
100 mA
0
V
o
ltage
(V)
Microload area
Area of
use
Standard
load area
Current (mA)
Hammer
Screwdriver
Do not allow the
Switch to drop and hit
the ground.
Do not place or drop
Switch.
Do not operate the
Switch with hard or
sharp objects.
In the interest of product improvement, specifications are subject to change without notice.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. A119-E1-04
相關PDF資料 |
PDF描述 |
|---|---|
| A22K-2AL-11 | ROTARY SWITCH-2POSITIONS, SPST, LATCHED, PANEL MOUNT |
| A2410EFGP-B | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| A2410FGH-B | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| A2425EH-10 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| A24110G | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A22EW | 功能描述:撥動開關 DPDT ON-ON .394 FLAT EXTENDED PC .4VA RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
| A22FA | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH UNIT PB ROUND/FLAT BLUE 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Access Push Button Switch Round Flat Button |
| A22-FA | 功能描述:開關配件 PB OPERATOR RND FLAT BLUE RoHS:否 制造商:C&K Components 類型:Cap 用于:Pushbutton Switches 設計目的: |
| A22FA01A | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:SWITCH PUSH SPST-NC 10A 110V 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Switch Push Button N.C. SPST Round Button 10A 440VAC 380VDC Alternate Contact Screw Panel Mount |
| A22-FA-01A | 功能描述:按鈕開關 SPST-NC ALT RND BLUE Flush actuator RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
發布緊急采購，3分鐘左右您將得到回復。