- 您現在的位置：買賣IC網 > PDF目錄294786 > A1425A-2VQG100C FPGA, 310 CLBS, 2500 GATES, 200 MHz, PQFP100 PDF資料下載
參數資料
| 型號： | A1425A-2VQG100C |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 310 CLBS, 2500 GATES, 200 MHz, PQFP100 |
| 封裝： | 1 MM HEIGHT, VQFP-100 |
| 文件頁數： | 4/68頁 |
| 文件大?。?/td> | 489K |
| 代理商： | A1425A-2VQG100C |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
1-186
Antifuse Connections
An antifuse is a “normally open” structure as opposed to the
normally closed fuse structure used in PROMs or PALs. The
use of antifuses to implement a programmable logic device
results in highly testable structures as well as an efficient
programming architecture. The structure is highly testable
because there are no preexisting connections; temporary
connections can be made using pass transistors. These
temporary connections can isolate individual antifuses to be
programmed as well as isolate individual circuit structures to
be tested. This can be done both before and after
programming. For example, all metal tracks can be tested for
continuity and shorts between adjacent tracks, and the
functionality of all logic modules can be verified.
Four types of antifuse connections are used in the routing
structure of the ACT 3 array. (The physical structure of the
antifuse is identical in each case; only the usage differs.)
Table 1 shows four types of antifuses.
Examples of all four types of connections are shown in
Module Interface
Connections to Logic and I/O modules are made through
vertical segments that connect to the module inputs and
outputs. These vertical segments lie on vertical tracks that
span the entire height of the array.
Module Input Connections
The tracks dedicated to module inputs are segmented by pass
transistors in each module row. During normal user
operation, the pass transistors are inactive, which isolates the
inputs of a module from the inputs of the module directly
above or below it. During certain test modes, the pass
transistors are active to verify the continuity of the metal
tracks. Vertical input segments span only the channel above
or the channel below. The logic modules are arranged such
that half of the inputs are connected to the channel above
and half of the inputs to segments in the channel below as
shown in Figure 9.
Module Output Connections
Module outputs have dedicated output segments. Output
segments extend vertically two channels above and two
channels below, except at the top or bottom of the array.
Output segments twist, as shown in Figure 10, so that only
four vertical tracks are required.
LVT Connections
Outputs may also connect to nondedicated segments called
Long Vertical Tracks (LVTs). Each module pair in the array
shares four LVTs that span the length of the column. Any
module in the column pair can connect to one of the LVTs in
the column using an FF connection. The FF connection uses
antifuses connected directly to the driver stage of the module
output, bypassing the isolation transistor. FF antifuses are
programmed at a higher current level than HF, VF, or XF
antifuses to produce a lower resistance value.
Antifuse Connections
In general every intersection of a vertical segment and a
horizontal segment contains an unprogrammed antifuse
(XF-type). One exception is in the case of the clock networks.
Clock Connections
To minimize loading on the clock networks, a subset of inputs
has antifuses on the clock tracks. Only a few of the C-module
and S-module inputs can be connected to the clock networks.
To further reduce loading on the clock network, only a subset
of the horizontal routing tracks can connect to the clock
inputs of the S-module.
Programming and Test Circuits
The array of logic and I/O modules is surrounded by test and
programming circuits controlled by the temporary special I/O
pins MODE, SDI, and DCLK. The function of these pins is
similar to all ACT family devices. The ACT 3 family also
includes support for two Actionprobe circuits allowing
complete observability of any logic or I/O module in the array
using the temporary special I/O pins, PRA and PRB.
Table 1 Antifuse Types
XF
Horizontal-to-Vertical Connection
HF
Horizontal-to-Horizontal Connection
VF
Vertical-to-Vertical Connection
FF
“Fast” Vertical Connection
相關PDF資料 |
PDF描述 |
|---|---|
| A1425A-2VQG100I | FPGA, 310 CLBS, 2500 GATES, PQFP100 |
| A1425A-PLG84C | FPGA, 310 CLBS, 2500 GATES, 125 MHz, PQCC84 |
| A1425A-PLG84I | FPGA, 310 CLBS, 2500 GATES, PQCC84 |
| A1425A-PQG100C | FPGA, 310 CLBS, 2500 GATES, 125 MHz, PQFP100 |
| A1425A-PQG100I | FPGA, 310 CLBS, 2500 GATES, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1425A-2VQG100I | 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 2.5K GATES 310 CELLS 200MHZ 0.8UM 5V 100VQFP - Trays |
| A1425A-3PL84C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| A1425A-3PL84I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| A1425A-3PQ100C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| A1425A-3PQ100I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
發布緊急采購，3分鐘左右您將得到回復。