參數資料
型號： A1415A-VQ100C
廠商： Microsemi SoC
文件頁數： 21/90頁
文件大小： 0K
描述： IC FPGA 1500 GATES 100-VQFP
標準包裝： 90
系列： ACT™ 3
LAB/CLB數： 200
輸入/輸出數： 80
門數： 1500
電源電壓： 4.5 V ~ 5.5 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 70°C
封裝/外殼： 100-TQFP
供應商設備封裝： 100-VQFP（14x14）
Detailed Specifications
2- 20
R e visio n 3
Tightest Delay Distributions
Propagation delay between logic modules depends on the resistive and capacitive loading of the routing
tracks, the interconnect elements, and the module inputs being driven. Propagation delay increases as
the length of routing tracks, the number of interconnect elements, or the number of inputs increases.
From a design perspective, the propagation delay can be statistically correlated or modeled by the fanout
(number of loads) driven by a module. Higher fanout usually requires some paths to have longer lengths
of routing track. The ACT 3 family delivers the tightest fanout delay distribution of any FPGA. This tight
distribution is achieved in two ways: by decreasing the delay of the interconnect elements and by
decreasing the number of interconnect elements per path.
Microsemi’s patented PLICE antifuse offers a very low resistive/capacitive interconnect. The ACT 3
family’s antifuses, fabricated in 0.8 micron m lithography, offer nominal levels of 200
Ω resistance and 6
femtofarad (fF) capacitance per antifuse. The ACT 3 fanout distribution is also tighter than alternative
devices due to the low number of antifuses required per interconnect path. The ACT 3 family’s
proprietary architecture limits the number of antifuses per path to only four, with 90% of interconnects
using only two antifuses.
The ACT 3 family’s tight fanout delay distribution offers an FPGA design environment in which fanout can
be traded for the increased performance of reduced logic level designs. This also simplifies performance
estimates when designing with ACT 3 devices.
Timing Characteristics
Timing characteristics for ACT 3 devices fall into three categories: family dependent, device dependent,
and design dependent. The input and output buffer characteristics are common to all ACT 3 family
members. Internal routing delays are device dependent. Design dependency means actual delays are
not determined until after placement and routing of the user’s design is complete. Delay values may then
be determined by using the ALS Timer utility or performing simulation with post-layout delays.
Critical Nets and Typical Nets
Propagation delays are expressed only for typical nets, which are used for initial design performance
evaluation. Critical net delays can then be applied to the most time-critical paths. Critical nets are
determined by net property assignment prior to placement and routing. Up to 6% of the nets in a design
may be designated as critical, while 90% of the nets in a design are typical.
Long Tracks
Some nets in the design use long tracks. Long tracks are special routing resources that span multiple
rows, columns, or modules. Long tracks employ three and sometimes four antifuse connections. This
increases capacitance and resistance, result ng in longer net delays for macros connected to long tracks.
Typically up to 6% of nets in a fully utilized device require long tracks. Long tracks contribute
approximately 4 ns to 14 ns delay. This additional delay is represented statistically in higher fanout
(FO = 8) routing delays in the datasheet specifications section.
Table 2-14 Logic Module and Routing Delay by Fanout (ns); Worst-Case Commercial Conditions
Speed Grade
FO = 1
FO = 2
FO = 3
FO = 4
FO = 8
ACT 3 –3
2.9
3.2
3.4
3.7
4.8
ACT 3 –2
3.3
3.7
3.9
4.2
5.5
ACT 3 –1
3.7
4.2
4.4
4.8
6.2
ACT 3 STD
4.3
4.8
5.1
5.5
7.2
Notes:
1. Obtained by added tRD(x=FO) to tPD from the Logic Module Timing Characteristics Tables found in this
datasheet.
2. The –2 and –3 speed grades have been discontinued. Refer to
相關PDF資料
PDF描述
A1415A-VQG100C IC FPGA 1500 GATES 100-VQFP
A54SX08-1PQ208I IC FPGA SX 12K GATES 208-PQFP
A54SX16-1PQ208 IC FPGA SX 24K GATES 208-PQFP
GMC60DRXN-S734 CONN EDGECARD 120PS DIP .100 SLD
GMC60DRXH-S734 CONN EDGECARD 120PS DIP .100 SLD
相關代理商/技術參數
參數描述
A1415A-VQ100I 功能描述:IC FPGA 1500 GATES 100-VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ACT™ 3 產品培訓模塊:Three Reasons to Use FPGA's in Industrial Designs Cyclone IV FPGA Family Overview 特色產品:Cyclone? IV FPGAs 標準包裝:60 系列:CYCLONE® IV GX LAB/CLB數:9360 邏輯元件/單元數:149760 RAM 位總計:6635520 輸入/輸出數:270 門數:- 電源電壓:1.16 V ~ 1.24 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:484-BGA 供應商設備封裝:484-FBGA（23x23）
A1415A-VQ100M 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 Family 1.5K Gates 200 Cells 125MHz 0.8um Technology 5V 100-Pin VQFP 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 1.5K GATES 200 CELLS 125MHZ 0.8UM 5V 100VQFP - Trays 制造商:Microsemi Corporation 功能描述:IC FPGA 80 I/O 100VQFP 制造商:Microsemi Corporation 功能描述:IC FPGA 1500 GATES 100-VQFP MIL
A1415A-VQG100C 功能描述:IC FPGA 1500 GATES 100-VQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ACT™ 3 標準包裝:40 系列:SX-A LAB/CLB數:6036 邏輯元件/單元數:- RAM 位總計:- 輸入/輸出數:360 門數:108000 電源電壓:2.25 V ~ 5.25 V 安裝類型:表面貼裝 工作溫度:0°C ~ 70°C 封裝/外殼:484-BGA 供應商設備封裝:484-FPBGA（27X27）
A1415A-VQG100I 功能描述:IC FPGA 1500 GATES 100-VQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ACT™ 3 產品培訓模塊:Three Reasons to Use FPGA's in Industrial Designs Cyclone IV FPGA Family Overview 特色產品:Cyclone? IV FPGAs 標準包裝:60 系列:CYCLONE® IV GX LAB/CLB數:9360 邏輯元件/單元數:149760 RAM 位總計:6635520 輸入/輸出數:270 門數:- 電源電壓:1.16 V ~ 1.24 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:484-BGA 供應商設備封裝:484-FBGA（23x23）
A1415A-VQG100M 制造商:Microsemi Corporation 功能描述:FPGA ACT 3 1.5K GATES 200 CELLS 125MHZ 0.8UM 5V 100VQFP - Trays 制造商:Microsemi Corporation 功能描述:IC FPGA 80 I/O 100VQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*