- 您現在的位置：買賣IC網 > PDF目錄67355 > A1392SEHLT-T MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | A1392SEHLT-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT |
| 封裝： | 2 X 3 MM, 0.75 MM HEIGHT, LEAD FREE, DFN-6 |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 480K |
| 代理商： | A1392SEHLT-T |
Micro Power 3 V Linear Hall Effect Sensor ICs
with Tri-State Output and User Selectable Sleep Mode
A1391, A1392,
A1393, and A1395
10
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Device Low-Power Functionality
A139x are low-power Hall effect sensor ICs that are perfect for
power sensitive customer applications. The current consumption
of these devices is typically 3.2 mA, while the device is in the
active mode, and less than 25 μA when the device is in the sleep
mode. Toggling the logic level signal connected to the SLEEP pin
drives the device into either the active mode or the sleep mode.
A logic low sleep signal drives the device into the sleep mode,
while a logic high sleep signal drives the device into the active
mode.
In the case in which the VREF pin is powered before the VCC
pin, the device will not operate within the specified limits until
the supply voltage is equal to the reference voltage. When the
device is switched from the sleep mode to the active mode, a time
defined by tPON must elapse before the output of the device is
valid. The device output transitions into the high impedance state
approximately tPOFF seconds after a logic low signal is applied to
the SLEEP pin (see figure 1).
If possible, it is recommended to power-up the device in the
sleep mode. However, if the application requires that the device
be powered on in the active mode, then a 10 kΩ resistor in series
with the SLEEP pin is recommended. This resistor will limit the
current that flows into the SLEEP pin if certain semiconductor
junctions become forward biased before the ramp up of the volt-
age on the VCC pin. Note that this current limiting resistor is not
required if the user connects the SLEEP pin directly to the VCC
pin. The same precautions are advised if the device supply is
powered-off while power is still applied to the SLEEP pin.
B field
VCC
VSLEEP
ICC
VOUT
tPON
+B
0
–B
tPOFF
HIGH
IMPEDANCE
HIGH
IMPEDANCE
HIGH
IMPEDANCE
Figure 1. A139x Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| A1393SEHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 3.1V, RECTANGULAR, SURFACE MOUNT |
| A1642LKTN-I2-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 3-100mT, RECTANGULAR, THROUGH HOLE MOUNT |
| A3421LKA-TL | MAGNETIC FIELD SENSOR-HALL EFFECT, -28-28mT, 0.21-0.50V, RECTANGULAR, THROUGH HOLE MOUNT |
| A3422EKA-TL | MAGNETIC FIELD SENSOR-HALL EFFECT, -7.5-7.5mT, 0.21-0.50V, RECTANGULAR, THROUGH HOLE MOUNT |
| A3515EUA | MAGNETIC FIELD SENSOR-HALL EFFECT, 1mT, 0.2-4.7V, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1392SEHLT-T | 制造商:Allegro MicroSystems 功能描述:Hall Effect IC |
| A1392SEHLT-TCUT | 制造商:Allegro MicroSystems LLC 功能描述: |
| A1392SEHLX-T | 制造商:Allegro MicroSystems 功能描述:LOW POWER LINEAR HALL-EFFECT S 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC HALL EFFECT SENSOR 6-MLP |
| A1393 | 制造商:Hakko 功能描述:A1393 Nozzle |
| A1393/P | 制造商:HAKKO Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。