- 您現在的位置：買賣IC網 > PDF目錄67355 > A1351KKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | A1351KKTTN-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 0.20-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, SIP-4 |
| 文件頁數： | 9/23頁 |
| 文件大小： | 654K |
| 代理商： | A1351KKTTN-T |
A1351
High Precision Linear Hall Effect Sensor IC
with a Push/Pull, Pulse Width Modulated Output
17
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
(Decimal Equivalent)
Code 5
Bit Field Selection
Address Code Format
Code in Binary
Fuse Blowing
Target Bits
Fuse Blowing
Address Code Format
(Binary)
1 0 1
Bit 2
Bit 0
Code 4
Code 1
(Decimal Equivalents)
Figure 3. Example of code 5 broken into its binary components,
equaling code 4 and code 1.
Locking the Device
After the desired code for each parameter is programmed, the
device can be locked to prevent further programming of any
parameters. See the Lock Mode section for lock pulse sequence.
Additional Guidelines
The additional guidelines in this section should be followed to
ensure the proper behavior of these devices:
A 0.1 μF blowing capacitor, CBLOW, must be mounted between
the PWMOUT pin and the GND pin during programming, to
ensure enough current is available to blow fuses.
The final application capacitance, CL, should be used when
measuring the output duty cycle during programming. (The
maximum load capacitance is 14.7 nF for proper operation.)
The blowing capacitor, CBLOW, should be removed during
measurements; it should only be applied when addressing bit
fields and when blowing fuses.
The power supply used for programming must be capable of
delivering at least 26 V and 300 mA.
Be careful to observe the tLOW delay time before powering
down the device after blowing each bit.
The following programming order is recommended:
1. PWM carrier frequency
2. Coarse D(Q)
3. Sens
4. D(Q)
5. LOCK (only after all other parameters have been
programmed and validated, because this prevents any further
programming of the device)
Figure 4. Example of programming pulses applied to the PWMOUT pin that result in permanent parameter settings. In this example, the register
corresponding to key 1 is selected (twice) and code 5 is addressed and blown (in two stages).
相關PDF資料 |
PDF描述 |
|---|---|
| A1354KKTTN-T | MAGNETIC FIELD SENSOR-HALL EFFECT, RECTANGULAR, THROUGH HOLE MOUNT |
| A1382ELHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1381LLHLT-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, SURFACE MOUNT |
| A1384LUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
| A1383EUA-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.35-4.65V, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1351LKTTN-T | 功能描述:IC SENSOR HALL EFFECT 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1352-035 | 制造商:AVX Corporation 功能描述: |
| A1352-037 | 制造商:AVX Corporation 功能描述: |
| A13532-43N | 制造商:Harris Corporation 功能描述: |
| A1354 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:High Precision 2-Wire Linear Hall Effect Sensor IC with Pulse Width Modulated Output |
發布緊急采購，3分鐘左右您將得到回復。