- 您現在的位置：買賣IC網 > PDF目錄352488 > A1101 (Allegro MicroSystems, Inc.) Continuous-Time Switch Family PDF資料下載
參數資料
| 型號： | A1101 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Continuous-Time Switch Family |
| 中文描述： | 連續時間開關系列 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 428K |
| 代理商： | A1101 |
7
A1101-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
115 Northeast Cutoff, Box 15036
www.allegromicro.com
Allegro MicroSystems, Inc.
Continuous-Time Switch Family
A1101, A1102, A1103, A1104, and A1106
Functional Description
OPERATION
The output of these devices switches low (turns on) when a
magnetic field (south polarity) perpendicular to the Hall sen-
sor exceeds the operate point threshold, BOP. After turn-on, the
output is capable of sinking 25 mA and the output voltage is
VOUT(SAT). When the magnetic field is reduced below the release
point, BRP, the device output goes high (turns off). The differ-
ence in the magnetic operate and release points is the hysteresis,
Bhys, of the device. This built-in hysteresis allows clean switch-
ing of the output, even in the presence of external mechanical
vibration and electrical noise.
Powering-on the device in the hysteresis region, less than BOP
and higher than BRP, allows an indeterminate output state. The
correct state is attained after the first excursion beyond BOP or
BRP.
CONTINUOUS-TIME BENEFITS
Continuous-time devices, such as the A110x family, offer the
fastest available power-on settling time and frequency response.
Due to offsets generated during the IC packaging process,
continuous-time devices typically require programming after
packaging to tighten magnetic parameter distributions. In con-
trast, chopper-stabilized switches employ an offset cancellation
technique on the chip that eliminates these offsets without the
need for after-packaging programming. The tradeoff is a longer
settling time and reduced frequency response as a result of the
chopper-stabilization offset cancellation algorithm.
The choice between continuous-time and chopper-stabilized
designs is solely determined by the application. Battery manage-
ment is an example where continuous-time is often required. In
these applications, VCC is chopped with a very small duty cycle
in order to conserve power (refer to figure 2). The duty cycle
is controlled by the power-on time, tPO, of the device. Because
continuous-time devices have the shorter power-on time, they
are the clear choice for such applications.
For more information on the chopper stabilization technique,
refer to Technical Paper STP 97-10, Monolithic Magnetic Hall
Sensor Using Dynamic Quadrature Offset Cancellation and
Technical Paper STP 99-1, Chopper-Stabilized Amplifiers with a
Track-and-Hold Signal Demodulator.
Figure 1. Switching Behavior of Unipolar Switches. On the horizontal axis, the B+ direction indicates increasing south polarity magnetic field
strength, and the B– direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This behavior can
be exhibited when using a circuit such as that shown in Panel B.
B
OP
B
RP
BHYS
VCC
V
OUT
VOUT(SAT)
Switch
to
Low
Switch
to
High
B+
B–
V+
0
(A)
(B)
VCC
VS
Sensor Output
GND
VOUT
RL
A110x
相關PDF資料 |
PDF描述 |
|---|---|
| A1101ELHLT-T | Continuous-Time Switch Family |
| A3150UA-LT | 320 x 240 pixel format, CFL backlight available with power harness |
| A3281ELH | HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION |
| A1181ELHLT | Sensitive Two-Wire Field-Programmable Chopper-Stabilized Unipolar Hall-Effect Switches |
| A1301ELHLT | Continuous-Time Ratiometric Linear Hall Effect Sensors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1101.0 | 制造商:DORMER 功能描述:DRILL BIT LONG 1MM 56MM 制造商:Farnell / Duratool 功能描述:DRILL LS HSS 1MM 制造商:DORMER 功能描述:DRILL BIT, LONG, 1MM, 56MM 制造商:Farnell / Duratool 功能描述:DRILL, LS, HSS, 1MM 制造商:Farnell / Duratool 功能描述:DRILL, LS, HSS, 1MM; Drill Bit Size Metric:1mm; Effective Length:33mm; Overall Length:56mm; Drill Bit Type:Twist / Jobber; Drill Point Diameter:1mm ;RoHS Compliant: NA |
| A1101.1 | 制造商:DORMER 功能描述:DRILL LS HSS 1.1MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.1MM |
| A1101.2 | 制造商:DORMER 功能描述:DRILL LS HSS 1.2MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.2MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.2MM; Drill Bit Size Metric:1.2mm; Effective Length:41mm; Overall Length:65mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Twist / Jobber; Drill Point Diameter:1.2mm; External Diameter:1.20mm; Material:HSS ;RoHS Compliant: NA |
| A1101.5 | 制造商:DORMER 功能描述:DRILL LS HSS 1.5MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.5MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.5MM; Drill Bit Size Metric:1.5mm; Effective Length:45mm; Overall Length:70mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Twist / Jobber; Drill Point Angle:118; Drill Point Diameter:1.5mm; External Diameter:1.50mm; ;RoHS Compliant: NA |
| A1101.8 | 制造商:DORMER 功能描述:DRILL LS HSS 1.8MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.8MM 制造商:DORMER 功能描述:DRILL, LS, HSS, 1.8MM; Drill Bit Size Metric:1.8mm; Effective Length:53mm; Overall Length:80mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Twist / Jobber; Drill Point Angle:118; Drill Point Diameter:1.8mm; External Diameter:1.80mm; ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。