- 您現在的位置：買賣IC網 > PDF目錄360656 > 9S12E128DGV1 (Motorola, Inc.) MC9S12E-Family Device User Guide V01.04 PDF資料下載
參數資料
| 型號： | 9S12E128DGV1 |
| 廠商： | Motorola, Inc. |
| 英文描述： | MC9S12E-Family Device User Guide V01.04 |
| 中文描述： | MC9S12E -系列設備的用戶手冊V01.04 |
| 文件頁數： | 84/156頁 |
| 文件大小： | 3077K |
| 代理商： | 9S12E128DGV1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁
Device User Guide — 9S12E128DGV1/D V01.04
84
2.3.14 PE1 /
IRQ — Port E input Pin 1 / Maskable Interrupt Pin
PE1 is always an input and can always be read. The PE1 pin is also the IRQ input used for requesting an
asynchronous interrupt to the MCU. During reset, the I bit in the condition code register (CCR) is set and
any IRQ interrupt is masked until software enables it by clearing the I bit. The IRQ is software
programmable to either falling edge-sensitive triggering or level-sensitive triggering based on the setting
of the IRQE bit in the IRQCR register. The IRQ is always enabled and configured to level-sensitive
triggering out of reset. It can be disabled by clearing IRQEN bit in the IRQCR register. There is an active
pull-up on this pin while in reset and immediately out of reset. The pullup can be turned off by clearing
PUPEE in the PUCR register.
2.3.15 PE0 / XIRQ — Port E input Pin 0 / Non Maskable Interrupt Pin
PE0 is always an input and can always be read. The PE0 pin is also the XIRQ input for requesting a
nonmaskable asynchronous interrupt to the MCU. During reset, the X bit in the condition code register
(CCR) is set and any XIRQ interrupt is masked until MCU software enables it by clearing the X bit.
Because the XIRQ input is level sensitive triggered, it can be connected to a multiple-source wired-OR
network. There is an active pull-up on this pin while in reset and immediately out of reset. The pullup can
be turned off by clearing PUPEE in the PUCR register.
2.3.16 PK7 / ECS / ROMCTL — Port K I/O Pin 7
PK7 is a general purpose input or output pin. During MCU expanded modes of operation, when the EMK
bit in the MODE register is set to 1, this pin is used as the emulation chip select output (ECS). In expanded
modes the PK7 pin can be used to determine the reset state of the ROMON bit in the MISC register. At
the rising edge of RESET, the state of the PK7 pin is latched to the ROMON bit. There is an active pull-up
on this pin while in reset and immediately out of reset. The pullup can be turned off by clearing PUPKE
in the PUCR register. Refer to the HCS12 MEBI Block Guide for further details. PK7 is not available in
the 80 pin package version.
2.3.17 PK6 / XCS — Port K I/O Pin 6
PK6 is a general purpose input or output pin. During MCU expanded modes of operation, when the EMK
bit in the MODE register is set to 1, this pin is used as an external chip select signal for most external
accesses that are not selected by ECS. There is an active pull-up on this pin while in reset and immediately
out of reset. The pullup can be turned off by clearing PUPKE in the PUCR register. Refer to the HCS12
MEBI Block Guide for further details. PK6 is not available in the 80 pin package version.
2.3.18 PK[5:0] / XADDR[19:14] — Port K I/O Pins [5:0]
PK[5:0] are general purpose input or output pins. In MCU expanded modes of operation, when the EMK
bit in the MODE register is set to 1, PK[5:0] provide the expanded address XADDR[19:14] for the external
bus. There are active pull-ups on PK[5:0] pins while in reset and immediately out of reset. The pullup can
be turned off by clearing PUPKE in the PUCR register. Refer to the HCS12 MEBI Block Guide for further
details. PK[5:0] are not available in the 80 pin package version.
F
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| 9S12H128 | 16-bit Microcontroller |
| 9S12H256 | 16-bit Microcontroller |
| 9S12HN64 | 16-bit Microcontroller |
| 9S12HZ128 | 16-bit Microcontroller |
| 9S12HZ256 | 16-bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9S12H128 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Microcontroller |
| 9S12H256 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Microcontroller |
| 9S12H256BDGV1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:9S12H256B Device Guide |
| 9S12HN64 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Microcontroller |
| 9S12HZ128 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。