- 您現在的位置：買賣IC網 > PDF目錄25514 > 951412AGLFT (INTEGRATED DEVICE TECHNOLOGY INC) 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF資料下載
參數資料
| 型號： | 951412AGLFT |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封裝： | 6.10 MM, 0.50 MM PITCH, GREEN, MO-153, TSSOP-56 |
| 文件頁數： | 10/25頁 |
| 文件大小： | 246K |
| 代理商： | 951412AGLFT |
18
ICS951412
0883L—04/26/06
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS951412
serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and
stored into a 5-bit internal data latch. At the end of Power-
On reset, (see AC characteristics for timing values), the
device changes the mode of operations for these pins to
an output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD
(logic 1) power supply or the GND (logic 0) voltage
potential. A 10 Kilohm (10K) resistor is used to provide
both the solid CMOS programming voltage needed during
the power-up programming period and to provide an
insignificant load on the output clock during the subsequent
operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the
series termination resistor to minimize the current loop
area. It is more important to locate the series termination
resistor close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| 951412BFLF | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951412AFLF | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951412AGLF | 220 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951413CGLF | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 951413CFLFT | 400 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 951412BFLF | 制造商:Integrated Device Technology Inc 功能描述:PLL Clock Synthesizer Dual 56-Pin SSOP Tube |
| 951412BFLFT | 制造商:Integrated Device Technology Inc 功能描述:PLL Clock Synthesizer Dual 56-Pin SSOP T/R |
| 951412BGLF | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| 951412BGLFT | 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| 951413-9010806-AR | 功能描述:集管和線殼 13P BD STCK HDR 1R THRU-HOLE 10U AU RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
發布緊急采購，3分鐘左右您將得到回復。