- 您現在的位置：買賣IC網 > PDF目錄24830 > 935269653115 (NXP SEMICONDUCTORS) 3.6 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 PDF資料下載
| 型號： | 935269653115 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 固定正電壓?jiǎn)温份敵鯨DO穩壓器 |
| 英文描述： | 3.6 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| 封裝： | 1.60 MM, PLASTIC, SOT-680-1, SO-5 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 235K |
| 代理商： | 935269653115 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁
Philips Semiconductors
Product data
SA57000-XX
CapFREE
150 mA, low-noise, low dropout regulator
with thermal protection
2003 Apr 01
7
TECHNICAL DESCRIPTION
General discussion
The SA57000-XX is a low dropout, low-quiescent current linear
regulator designed primarily for battery-powered applications and
stabilizes with or without input/output capacitors. The device delivers
up to 150 mA and is available with preset output voltages of 2.5 V,
2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.3 V, and 3.6 V for both SOT 23-5 and
WL-CSP packages.
The 1.23 band-gap reference is connected to the error amplifier’s
inverting input. The error amplifier compares this reference with the
feedback voltage and amplifies the difference. If the feedback
voltage is lower than the reference voltage, the pass-transistor gate
is pulled lower, which allows more current to pass to the output. The
output voltage is fed back through an internal resistor voltage divider
connected to the VOUT pin.
Band-gap
The band-gap circuitry generates a temperature independent
voltage by properly adding two voltages with negative and positive
temperature coefficient. The band-gap voltage is typically 1.23 volts
with a temperature variation of 5 mV over the temperature range
from –40
°C to +125 °C.
Low-pass filter
Low-pass filter is basically an RC filter with a low cut-off frequency.
No external capacitor is used. There is one comparator, which
turns on the bypass paths to charge or discharge the capacitor if the
output of the filter is higher or lower than the band-gap voltage by a
specified amount.
Output amplifier
The output amplifier is a folded-cascode PMOS amplifier which
controls the gate of the output transistor and sources the load
current. A portion of the output voltage is compared to the reference
voltage and a constant voltage is maintained at output. The output is
also monitored by a comparator which trips PWROK if the output
voltage falls below the nominal output level by a specified amount
due to low battery condition or any other reason. The current limiter
circuit monitors the output current and limits the load current to a
certain value to avoid any damage due to short circuit.
Bias circuit
The bias block provides bias currents and voltages for the other
blocks. It has a self start-up circuit and it can establish the bias
currents and voltages very fast.
Temperature sensor
The temperature sensor block monitors the die temperature and
flags PWROK when the temperature crosses 125
°C. If the die
temperature goes beyond 144
°C typical value, the output amplifier
is shut down. Both the temperatures corresponding to Power-OK or
shutdown have a hysteresis of 13
°C.
ESD protection
The standard ESD blocks protect the CMOS circuit against
electrostatic discharge (ESD).
PRWROK output
PWROK goes LOW when the output voltage goes out of regulation
as during drop-out, current limit or thermal shutdown. PowerOK is
an open-drain N-channel MOSFET. To obtain a logic-level output,
connect a 10 k
pull-up resistor from PWROK pin to VOUT pin. To
minimize current consumption, make this resistor as large as
practical. A 100 k
resistor works well for most applications. The
PowerOK is not active during shutdown.
Current limit
The SA57000-XX includes a current limiter that monitors and
controls the pass transistor’s gate voltage, limiting the output current
to 300 mA typical value. For design purposes, consider the current
limit to be 160 mA minimum value. The output can be shorted to
ground for an indefinite period of time without damaging the part.
Thermal-overload protection
When the junction temperature exceeds Tj = 144 _C typical value,
the thermal sensor signals the shutdown logic, turning off the output
amplifier and allowing the die to cool. The thermal sensor will turn
the output amplifier on again after the die’s junction temperature
decreases by 13
_C hysteresis value, resulting in a pulsed output
during continuous thermal overload conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| 935272488115 | 3.1 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| 935269650115 | 2.8 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| 935272487115 | 2.9 V FIXED POSITIVE LDO REGULATOR, 0.12 V DROPOUT, PDSO5 |
| 0803-7700-06 | VDSL 4 Band Solution CPE (NT) |
| 935269654118 | 10 1-BIT DRIVER, TRUE OUTPUT, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935269987557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-1US1-V1.8 SUBBED TO 935269987557 |
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
| 935270792551 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270792557 | 制造商:NXP Semiconductors 功能描述:IC BUFF DVR TRI-ST 16BIT 56VFBGA |
| 935270793551 | 制造商:NXP Semiconductors 功能描述:IC BUS TRCVR 3-ST 16BIT 56VFBGA |
發布緊急采購，3分鐘左右您將得到回復。