- 您現在的位置：買賣IC網 > PDF目錄42382 > 935268119112 (NXP SEMICONDUCTORS) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | 935268119112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 3.90 MM, 0.635 MM PITCH, PLASTIC, SOT-519-1, SSOP-16 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 128K |
| 代理商： | 935268119112 |
Philips Semiconductors
Product data
NE1617A
Temperature monitor for microprocessor systems
2001 Dec 14
13
Power-up default condition
Upon power-up reset (power is switched off-on), the NE1617A goes
into this default condition:
– Interrupt latch is cleared, the ALERT output is pulled HIGH by the
external pull-up resistor.
– The auto-conversion rate is at 0.25 Hz; conversion rate data is
02H.
– Temperature limits for both channels are +127
°C for high limit,
and –55
°C for low limit.
– Command pointer register is set to 00 for quickly reading the RIT.
Fault detection
The NE1617A has a fault detector to the diode connection. The
connection is checked when a conversion is initiated and the proper
flags are set if the fault condition has occurred.
D+ & D–
ALERT
OUTPUT
RET DATA
STORAGE
STATUS SET
FLAG
Opened
Low
127
°C
B2 and B4
Shorted
Low
127
°C
B4
SMBus interface
The device can communicate over a standard 2-wire serial interface
System Management Bus (SMBus) using the device pins SCLK and
SDATA. The device employs four standard SMBus protocols:
Write Byte, Read Byte, Send Byte and Receive Byte. Data formats
of those protocols are shown in Table 8 with following notifications:
– The SMBus master initiates data transfer by establishing a start
condition (S) and terminates data transfer by generating a stop
condition (P).
– Data is sent over the serial bus in sequence of 9 clock pulses
according to each 8-bit data byte followed by 1-bit status of the
device acknowledgement.
– The 7-bit slave address is equivalent to the selected address of
the device.
– The command byte is equivalent to the selected command of the
device register
– The send byte format is often used for the one-shot conversion
command.
– The receive byte format is used for quicker transfer data from a
device reading register which was previously selected by a read
byte format.
Table 8. SMBus programming format
Write byte format (for writing data byte to the device register):
S
ADDRESS
WR
ACK
COMMAND
ACK
DATA
ACK
P
7 bits
device address
1 bit = 0
by
device
8 bits
device register
by
device
8 bits
to register
by
device
Read byte format (for reading data byte from the device register):
S
ADDRESS
WR
ACK
COMMAND
ACK
S
ADDRESS
RD
ACK
DATA
NACK
P
7 bits
device address
1 bit = 0
by
device
8 bits
device register
by
device
7 bits
device address
1 bit = 1
by
device
8 bits
from
register
by
controller
Send byte format (for sending command without data, such as one-shot command):
S
ADDRESS
WR
ACK
COMMAND
ACK
P
7 bits
device address
1 bit = 0
by
device
8 bits
device register
by
device
Receive byte format (for continuously reading from device register):
S
ADDRESS
RD
ACK
DATA
NACK
P
7 bits
device address
1 bit = 1
by
device
8 bits
from register
by
controller
NOTES:
S = Start condition
P = Stop condition
ACK = Acknowledged
NACK = Not acknowledged
相關PDF資料 |
PDF描述 |
|---|---|
| 935268119118 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 935268498557 | PLL FREQUENCY SYNTHESIZER, 2500 MHz, PBCC24 |
| 935268498551 | PLL FREQUENCY SYNTHESIZER, 2500 MHz, PBCC24 |
| 935268498518 | PLL FREQUENCY SYNTHESIZER, 2500 MHz, PBCC24 |
| 935269131518 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
| 935269544557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3 |
| 935269987557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-1US1-V1.8 SUBBED TO 935269987557 |
| 935270713557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC CHP |
發布緊急采購，3分鐘左右您將得到回復。