- 您現在的位置：買賣IC網 > PDF目錄24817 > 935265527518 (NXP SEMICONDUCTORS) SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | 935265527518 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 封裝： | PLASTIC, QFP-64 |
| 文件頁數： | 25/55頁 |
| 文件大?。?/td> | 387K |
| 代理商： | 935265527518 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
1999 May 10
31
Philips Semiconductors
Preliminary specication
Universal Serial Bus (USB) CODEC
UDA1325
COMMAND DESCRIPTIONS
Command procedure
This chapter describes the commands that can be used by
the microcontroller to control the USB processor. There
are three basic types of commands:
Initialization commands
Data flow commands
General commands.
A command is represented by an 8 bit code. It can be
followed by one or more data write cycles or one or more
read cycles or a combination. The PSIE_MMU_READY
output connected to Port 3.4 of the microcontroller
indicates that the previous action (command write, data
read or data write) has completed. A new action can only
be initiated if PSIE_MMU_READY is TRUE. The data is
valid from the moment PSIE_MMU_READY becomes
TRUE.
The PSIE contains a number of interrupt registers, one for
each endpoint. Every time a transition occurs, the interrupt
flag for the involved endpoint is set. The PSIE_MMU_INT
connected to Port 3.3 is an OR function of all interrupt
registers.
Initialization commands
Initialization commands are used during the enumeration
process of the USB network. They are used to set the USB
assigned address, enable endpoints and select the
configuration of the device.
SET ADDRESS/ENABLE
Command: D0h.
Data: write 1 byte.
The set address/enable command is used to set the USB
assigned address and enable the function. The device
always powers up disabled and should be enabled after a
bus reset.
0
Address
Enable
0
1
2
3
4
5
6
7
0
00
0000
Power On Value
Table 24
READ ADDRESS/ENABLE
Command: D0h.
Data: read 1 byte.
The read address/enable command is used to read the
USB assigned address and the enable bit of the device.
The format of the data phase is the same as for the set
address/enable command.
SET ENDPOINT ENABLE
Command: D8h.
Data: write 1 byte.
The set endpoint enable command is used to set the
enable bits for the non default endpoints.
If the enable bit is ‘1’, the non default endpoints are
enabled, if ‘0’, the non default endpoints are disabled.
The function then only responds to the default control
endpoint.
After bus reset, the enable bit is set to ‘0’.
READ ENDPOINT ENABLE
Command: D8h.
Data: read 1 byte.
The read endpoint enable command is used to read the
enable bit for the non default endpoints of the function.
The format of the data phase is the same as for the set
endpoint enable command.
SET MODE
Command: F3h.
Data: write 1 byte.
BIT
DESCRIPTION
Address
the value written becomes
the device address
Enable
a ‘1’ enables this function
XXXXXXX
0
Enable
Reserved
76543210
Power On Value
相關PDF資料 |
PDF描述 |
|---|---|
| 935263513518 | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP64 |
| 08-50-0415 | Crimp Pin Contact; Contact Material:Brass; Contact Plating:Tin |
| 08-56-0401 | KK .044 Sq Pin 0.750 20 Gold |
| 08-50-0410 | 8500410 |
| 08-56-0406 | 8560406 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 935267356112 | 制造商:NXP Semiconductors 功能描述:IC TEA1507PN |
| 935268081112 | 制造商:NXP Semiconductors 功能描述:SUB ONLY IC |
| 935268721125 | 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R |
| 935269304128 | 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP |
| 935269544557 | 制造商:NXP Semiconductors 功能描述:SUB ONLY TDA9587-2US1-V1.3 |
發布緊急采購，3分鐘左右您將得到回復。