參數資料
型號： 935263837118
廠商： NXP SEMICONDUCTORS
元件分類： 其它接口
英文描述： SPECIALTY INTERFACE CIRCUIT, PQFP32
封裝： PLASTIC, SOT-401, LQFP-32
文件頁數： 5/35頁
文件大?。?/td> 208K
代理商： 935263837118
2000 Feb 22
13
Philips Semiconductors
Product specication
Gigabit Ethernet/Fibre Channel laser
drivers
TZA3041AHL; TZA3041BHL;
TZA3041U
Bias alarm for TZA3041AHL
The bias current alarm circuit detects whenever the bias
current is outside a predefined range, and generates a
flag. This feature can detect excessive bias current due to
laser ageing or laser malfunctioning. The current applied
to pin ALARMHI should be the maximum permitted bias
current value attenuated by a ratio of 1:1500. The current
applied to pin ALARMLO should be the minimum
permitted bias current value attenuated by a ratio of 1:300.
Like the reference currents for the laser current control
loop, the alarm reference currents can be set by
connecting external resistors between VCC(R) and
pins ALARMHI and ALARMLO (see Fig.8). The resistor
values can be calculated using the following formulae:
(9)
(10)
Example: The following reference currents are required to
limit the bias current range from 6 to 90 mA:
and
The corresponding resistor values are:
and
If the alarm condition is true, the voltage on pin ALARM
(see Fig.14) goes to a HIGH level (CMOS). This signal
could be used, for example, to drive pin ALS to disable the
laser driver; the signal to pin ALS has to be latched to
prevent oscillation.
A hysteresis of approximately 10% is applied to both alarm
functions. The attenuation ratios of 1:300 and 1:1500 are
valid if the bias current rises above the reference current
levels. If the bias current decreases, the ratios are 10%
lower.
Accuracy of voltage on inputs: ONE, ZERO,
ALARMLO, ALARMHI
It is important to consider the accuracy of the 1.5 V level
with respect to VCC(R) on pins ONE and ZERO if resistors
are used to set the reference currents. Although this value
is independent of VCC(R), deviations from 1.5 V can be
caused by:
Input current: At Tj =25 °C, the voltage between pin and
VCC varies from 1.58 V at an input current of 6 A, down
to 1.45 V at 65
A and 1.41 V at 100 A. The range
between 65
A and 100 A is only specified for
ALARMLO. In the application, the input current is
virtually fixed, so this variation has little effect.
Variation in batch and individual device characteristics,
not exceeding
±2% from the nominal product: This
variation can be compensated for where devices in the
application are individually trimmed.
Temperature: The variation in Tj is shown in Fig.15.
At 30
A (middle of the specified range) the total
variation in Tj is <1%, at 65 A it is <2% and at 6 Aitis
<3%.
R
ALARMHI
1.5
1500
×
I
OBIAS
() max
()
---------------------------------
=
[]
R
ALARMLO
1.5
300
×
I
O BIAS
() min
()
--------------------------------
=
[]
I
ALARMLO
610
3
–
×
300
---------------------
20
A
==
I
ALARMHI
90
10
3
–
×
1500
------------------------
60
A
==
R
ALARMHI
1.5
1500
×
90
10
3
–
×
----------------------------
25 k
==
R
ALARMLO
1.5
300
×
610
3
–
×
------------------------
75 k
==
handbook, halfpage
MGS909
20
43
VCC(R)
GND
ALARM
Fig.14 ALARM output.
相關PDF資料
PDF描述
935263838118 SPECIALTY INTERFACE CIRCUIT, PQFP32
935263842026 SPECIALTY INTERFACE CIRCUIT, UUC40
935263881112 SPECIALTY TELECOM CIRCUIT, PDSO28
935263881118 SPECIALTY TELECOM CIRCUIT, PDSO28
935263971112 SPECIALTY TELECOM CIRCUIT, PDSO28
相關代理商/技術參數
參數描述
935264217557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*