參數資料
型號: 935263292112
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 26/80頁
文件大?。?/td> 446K
代理商: 935263292112
1997 Dec 15
32
Philips Semiconductors
Product specication
8-bit microcontrollers
P83C524; P80C528; P83C528
13 BIT-LEVEL I2C INTERFACE
This bit-level serial I/O interface supports the I2C-bus (see
Fig.18). P1.6/SCL and P1.7/SDA are the serial I/O pins.
These two pins meet the I2C specification concerning the
input levels and output drive capability. Consequently,
these pins have an open drain output configuration. All
four modes of the I2C-bus are supported:
master transmitter
master receiver
slave transmitter
slave receiver.
The advantages of the bit-level I2C hardware compared
with a full software I2C implementation are:
the hardware can generate the SCL pulse
testing a single bit (RBF respectively, WBF) is sufficient
as a check for error free transmission.
The bit-level I2C hardware operates on serial bit level and
performs the following functions:
filtering the incoming serial data and clock signals
recognizing the START condition
generating a serial interrupt request SI after reception of
a START condition and the first falling edge of the serial
clock
recognizing the STOP condition
recognizing a serial clock pulse on the SCL line
latching a serial bit on the SDA line (SDI)
stretching the SCL LOW period of the serial clock to
suspend the transfer of the next serial data bit
setting Read Bit Finished (RBF) when the SCL clock
pulse has finished and Write Bit Finished (WBF) if there
is no arbitration loss detected (i.e. SDA = 0 while
SDO = 1)
setting a serial clock LOW-to-HIGH detected (CLH) flag
setting a Bus Busy (BB) flag on a START condition and
clearing this flag on a STOP condition
releasing the SCL line and clearing the CLH, RBF and
WBF flags to resume transfer of the next serial data bit
generating an automatic clock if the single bit data
register S1BIT is used in master mode.
The following functions must be done in software:
handling the I2C START interrupts
converting serial to parallel data when receiving
converting parallel to serial data when transmitting
comparing the received slave address with its own
interpreting the acknowledge information
guarding the I2C status if RBF or WBF = 0.
additionally, if acting as master:
generating START and STOP conditions
handling bus arbitration
generating serial clock pulses if S1BIT is not used.
Three SFRs control the bit-level I2C interface: S1INT,
S1BIT and S1SCS.
相關PDF資料
PDF描述
0666-0-57-15-32-02-10-0 BERYLLIUM COPPER, TIN LEAD (200) OVER NICKEL FINISH, PCB TERMINAL
0666-0-57-80-32-27-10-0 BERYLLIUM COPPER, GOLD (30) OVER NICKEL FINISH, PCB TERMINAL
0667520000 SAKS 3/35,1-1/4X1/4,KRG,BN
935074280518 TELECOM, PAGING RECEIVER, PQFP32
935260966005 TELECOM, PAGING RECEIVER, UUC28
相關代理商/技術參數
參數描述
935264217557 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935267356112 制造商:NXP Semiconductors 功能描述:IC TEA1507PN
935268081112 制造商:NXP Semiconductors 功能描述:SUB ONLY IC
935268721125 制造商:NXP Semiconductors 功能描述:Buffer/Line Driver 1-CH Non-Inverting 3-ST CMOS 5-Pin TSSOP T/R
935269304128 制造商:ST-Ericsson 功能描述:IC AUDIO CODEC W/TCH SCRN 48LQFP