參數資料
型號： 935073600557
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MICROCONTROLLER, PQFP44
封裝： 10 X 10 X 1.75 MM, PLASTIC, QFP-44
文件頁數： 37/80頁
文件大?。?/td> 446K
代理商： 935073600557
1997 Dec 15
42
Philips Semiconductors
Product specication
8-bit microcontrollers
P83C524; P80C528; P83C528
15.2
Idle Mode
The instruction that sets PCON.0 is the last instruction
executed in the normal operating mode before Idle mode
is activated. Once in the Idle mode, the CPU status is
preserved in its entirety: the Stack Pointer, Program
Counter, Program Status Word, Accumulator, RAM and all
other registers maintain their data during Idle mode. The
status of external pins during Idle mode is shown in
Table 28.
There are three ways to terminate the Idle mode:
Activation of any enabled interrupt will cause PCON.0 to
be cleared by hardware terminating Idle mode. The
interrupt is serviced, and following return from interrupt
instruction RETI, the next instruction to be executed will
be the one which follows the instruction that wrote a
logic 1 to PCON.0.
The flag bits GF0 and GF1 may be used to determine
whether the interrupt was received during normal
execution or during the Idle mode. For example, the
instruction that writes to PCON.0 can also set or clear
one or both flag bits. When Idle mode is terminated by
an interrupt, the service routine can examine the status
of the flag bits.
The second way of terminating the Idle mode is with an
external hardware reset. Since the oscillator is still
running, the hardware reset is required to be active for
two machine cycles (24 oscillator periods) to complete
the reset operation.
The third way of terminating the Idle mode is by internal
watchdog reset.
15.3
Power-down Mode
The instruction that sets PCON.1 is the last executed prior
to going into the Power-down mode. The oscillator is
stopped. Note that the Power-down mode also can be
entered when the watchdog has been enabled. The
Power-down mode can be terminated by an external
RESET in the same way as in the 80C51 or in addition by
any one of the two external interrupts, IE0 or IE1 (see
Section 15.4). A reset generated by the WDT terminates
the Power-down mode in the same way as an external
RESET.
The status of the external pins during Power-down mode
is shown in Table 28. If the Power-down mode is activated
while in external program memory, the port data that is
held in the P2 SFR is restored to Port 2. If the data is a
logic 1, the port pin is held HIGH during the Power-down
mode by the strong pull-up transistor p1 (see Fig.13).
Table 28 Status of the external pins during Idle and Power-down modes
MODE
MEMORY
ALE
PSEN
PORT 0
PORT 1
PORT 2
PORT 3
Idle
internal
1
port data
Idle
external
1
oating
port data
address
port data
Power-down
internal
0
port data
Power-down
external
0
oating
port data
相關PDF資料
PDF描述
935263292112 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQCC44
0666-0-57-15-32-02-10-0 BERYLLIUM COPPER, TIN LEAD (200) OVER NICKEL FINISH, PCB TERMINAL
0666-0-57-80-32-27-10-0 BERYLLIUM COPPER, GOLD (30) OVER NICKEL FINISH, PCB TERMINAL
0667520000 SAKS 3/35,1-1/4X1/4,KRG,BN
935074280518 TELECOM, PAGING RECEIVER, PQFP32
相關代理商/技術參數
參數描述
935079-000 制造商:TE Connectivity 功能描述:55A1841-16-MST4-9CS2275 - Cable Rools/Shrink Tubing
935087-000 制造商:TE Connectivity 功能描述:301A511-51-05/164-0 - Bulk
935087N001 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 制造商:TE Connectivity 功能描述:301A511-51-05/164-CS7092 - Bulk
9350DC-200-0GZZZA 制造商:Siemens 功能描述:
9350DC-200-0ZZZTA 制造商:Siemens 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*