- 您現在的位置：買賣IC網 > PDF目錄24670 > 933821300112 (NXP SEMICONDUCTORS) TELEPHONE SPEECH CKT, PDIP18 PDF資料下載
參數資料
| 型號： | 933821300112 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | TELEPHONE SPEECH CKT, PDIP18 |
| 封裝： | 0.300 INCH, PLASTIC, SOT-102, DIP-18 |
| 文件頁數： | 26/29頁 |
| 文件大小： | 231K |
| 代理商： | 933821300112 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁
June 1990
6
Philips Semiconductors
Product specication
Low voltage versatile telephone
transmission circuit with dialler interface
TEA1067
Microphone inputs (MIC
+ and MIC) and gain
adjustment pins (GAS1 and GAS2)
The TEA1067 has symmetrical microphone inputs. Its
input impedance is 64 k
(2 × 32 k) and its voltage gain
is typically 52 dB (when R7 = 68 k
, see Fig.14). Dynamic,
magnetic, piezoelectric or electret (with built-in FET source
followers) microphones can be used. Microphone
arrangements are shown in Fig.11.
The gain of the microphone amplifier can be adjusted
between 44 dB and 52 dB to suit the sensitivity of the
transducer in use. The gain is proportional to the value of
R7 which is connected between GAS1 and GAS2. Stability
is ensured by the external capacitor C6 which is connected
between GAS1 and SLPE. The value of C6 is 100 pF but
this may be increased to obtain a first-order low-pass filter.
The cut-off frequency corresponds to the time constant
R7
× C6.
Mute input (MUTE)
When MUTE is HIGH the DTMF input is enabled and the
microphone and receiving amplifier inputs are inhibited.
The reverse is true when MUTE is LOW or open-circuit.
MUTE switching causes only negligible clicking on the
earpiece outputs and line. If the number of parallel sets in
use causes a drop in line current to below 6 mA the speech
amplifiers remain active independent to the DC level
applied to the MUTE input.
Fig.4 Equivalent impedance circuit.
Rp = 16.2 k
Leq = C3 × R9 × Rp
handbook, halfpage
MBA454
R9
20
REG
LN
C3
4.7
F
Rp
Vref
Leq
VCC
VEE
C1
100
F
R1
Dual-tone multi-frequency input (DTMF)
When the DTMF input is enabled dialling tones may be
sent onto the line. The voltage gain from DTMF to LN is
typically 25.5 dB (when R7 = 68 k
) and varies with R7 in
the same way as the microphone gain. The signalling
tones can be heard in the earpiece at a low level
(confidence tone).
Receiving Amplier (IR, QR
+, QR and GAR)
The receiving amplifier has one input (IR), one
non-inverting complementary output (QR
+) and an
inverting complementary output (QR
). These outputs
may be used for single-ended or differential drive
depending on the sensitivity and type of earpiece used
(see Fig.12). IR to QR
+ gain is typically 31 dB (when
R4 = 100 k
), this is sufficient for low-impedance
magnetic or dynamic microphones which are suited for
single-ended drive. Using both outputs for differential drive
gives an additional gain of 6 dB. This feature can be used
when the earpiece impedance exceeds 450
(high-impedance dynamic or piezoelectric types).
The receiving amplifier gain can be adjusted between 20
and 39 dB with single-ended drive and between 26 and
45 dB with differential drive, to match the sensitivity of the
transducer in use. The gain is set with the value of R4
which is connected between GAR and QR
+. Overall
receive gain between LN and QR
+ is calculated by
substracting the anti-sidetone network attenuation (32 dB)
from the amplifier gain. Two external capacitors C4 and
C7, ensure stability. C4 is normally 100 pF and C7 is
10
× the value of C4. The value of C4 may be increased to
obtain a first-order low-pass filter. The cut-off frequency
will depend on the time constant R4
× C4.
The output voltage of the receiving amplifier is specified for
continuous-wave drive. The maximum output voltage will
be higher under speech conditions where the peak to RMS
ratio is higher.
相關PDF資料 |
PDF描述 |
|---|---|
| 933888910623 | F/FAST SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT BIDIRECTIONAL BINARY COUNTER, PDSO16 |
| 933794820602 | F/FAST SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT BIDIRECTIONAL BINARY COUNTER, PDIP16 |
| 933890190112 | 800 mA, 55 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
| 933890190126 | 800 mA, 55 V, NPN, Si, SMALL SIGNAL TRANSISTOR, TO-92 |
| 0561188328 | PHOSPHOR BRONZE, TIN (40) FINISH, WIRE TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 933821820115 | 制造商:NXP Semiconductors 功能描述:TRANS NPN SW 40V 100MA SOT89-3 |
| 9338-2M | 制造商:PRO ELEC 功能描述:EXTENSION LEAD 3WAY 2M 制造商:PRO ELEC 功能描述:EXTENSION LEAD, 3WAY, 2M |
| 9338359 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 933844001 | 制造商:Hirschmann Electronics GmbH & Co Kg 功能描述:TEST LEAD BLACK 1.2MBNC TO 0.64MM SKT 制造商:Hirschmann Electronics GmbH & Co Kg 功能描述:TEST LEAD, BLACK, 1.2M,BNC TO 0.64MM SKT 制造商:Hirschmann Electronics GmbH & Co Kg 功能描述:TEST LEAD, BLACK, 1.2M,BNC TO 0.64MM SKT, Lead Length:1.2m, Insulator Colour:Black, Test Connector Type A:BNC Plug, Test Connector Type B:Probe, Voltage Rating:60V, SVHC:No SVHC (20-Jun-2013), Connector Type A:BNC Plug, Connector , RoHS Compliant: Yes 制造商:SKS KONTAKTTECHNIK GMBH 功能描述:BNC-0.64MM ADAPTER CABLE |
| 9338-5M | 制造商:PRO ELEC 功能描述:EXTENSION LEAD 3WAY 5M 制造商:PRO ELEC 功能描述:EXTENSION LEAD, 3WAY, 5M |
發布緊急采購，3分鐘左右您將得到回復。