- 您現在的位置：買賣IC網 > PDF目錄364551 > 8XL52 (Intel Corp.) FUSE KIT, ASSORTED; Depth, external:165mm; Height:50mm; Width, external:260mm PDF資料下載
參數資料
| 型號： | 8XL52 |
| 廠商： | Intel Corp. |
| 英文描述： | FUSE KIT, ASSORTED; Depth, external:165mm; Height:50mm; Width, external:260mm |
| 中文描述： | 低壓CHMOS單片8位微控制器 |
| 文件頁數： | 5/20頁 |
| 文件大小： | 284K |
| 代理商： | 8XL52 |
8XL52/54/58
ALE: Address Latch Enable output pulse for latching
the low byte of the address during accesses to ex-
ternal memory. This pin (ALE/PROG) is also the
program pulse input during OTP ROM programming
for the 87L5X.
In normal operation ALE is emitted at a constant
rate of
(/6
the oscillator frequency, and may be used
for external timing or clocking purposes. Note, how-
ever, that one ALE pulse is skipped during each ac-
cess to external Data Memory.
If desired, ALE operation can be disabled by setting
bit 0 of SFR location 8EH. With this bit set, the pin is
weakly pulled high. However, the ALE disable fea-
ture will be suspended during a MOVX or MOVC in-
struction, idle mode, power down mode and ICE
mode. The ALE disable feature will be terminated by
reset. When the ALE disable feature is suspended or
terminated, the ALE pin will no longer be pulled up
weakly. Setting the ALE-disable bit has no affect if
the microcontroller is in external execution mode.
Throughout the remainder of this data sheet, ALE
will refer to the signal coming out of the ALE/PROG
pin, and the pin will be referred to as the ALE/PROG
pin.
PSEN: Program Store Enable is the read strobe to
external Program Memory.
When the 8XL5X is executing code from external
Program Memory, PSEN is activated twice each ma-
chine cycle, except that two PSEN activations are
skipped during each access to external Data Memo-
ry.
EA/V
PP
: External Access enable. EA must be
strapped to VSS in order to enable the device to
fetch code from external Program Memory locations
0000H to 0FFFH. Note, however, that if either of the
Program Lock bits are programmed, EA will be inter-
nally latched on reset.
EA must be strapped to V
CC
for internal program
executions.
This pin also receives the programming supply volt-
age (V
PP
) during OTP ROM programming.
XTAL1: Input to the inverting oscillator amplifier.
XTAL2: Output from the inverting oscillator amplifier.
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respec-
tively, of a inverting amplifier which can be config-
ured for use as an on-chip oscillator, as shown in
Figure 3. Either a quartz crystal or ceramic resonator
may be used. More detailed information concerning
the use of the on-chip oscillator is available in Appli-
cation Note AP-155, ‘‘Oscillators for Microcontrol-
lers.’’
To drive the device from an external clock source,
XTAL1 should be driven, while XTAL2 floats, as
shown in Figure 4. There are no requirements on the
duty cycle of the external clock signal, since the in-
put to the internal clocking circuitry is through a di-
vide-by-two flip-flop, but minimum and maximum
high and low times specified on the data sheet must
be observed.
An external oscillator may encounter as much as a
100 pF load at XTAL1 when it starts up. This is due
to interaction between the amplifier and its feedback
capacitance. Once the external signal meets the V
IL
and V
IH
specifications the capacitance will not ex-
ceed 20 pF.
272468–4
C1, C2
e
30 pF
g
10 pF for Crystals
For Ceramic Resonators, contact resonator manufacturer.
Figure 3. Oscillator Connections
272468–5
Figure 4. External Clock Drive Configuration
IDLE MODE
The user’s software can invoke the Idle Mode. When
the microcontroller is in this mode, power consump-
tion is reduced. The Special Function Registers and
the onboard RAM retain their values during Idle, but
the processor stops executing instructions. Idle
Mode will be exited if the chip is reset or if an en-
abled interrupt occurs. The PCA timer/counter can
optionally be left running or paused during Idle
Mode.
5
相關PDF資料 |
PDF描述 |
|---|---|
| A-1855-06111-UNILAP100E | INSTALLATION TESTER |
| A-1855-06211GB-UNILAP100XE | INSTALLATION TESTER |
| A-225 | Preamp， Non-Audio |
| A-2510-11000-00(SE102-1) | CHART RECORDER 1 CHANNEL DC |
| A-H01 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8XL54 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XL58 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LOW VOLTAGE CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLERS |
| 8XLT12.5TAM/BLK)2UGRAAGPS | 功能描述:按鈕開關 8POS BLK P/B ASSY RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
| 8XTA102UGRAAGPN | 功能描述:SWITCH ASSY 8 POS CUSTOM RoHS:否 類別:開關 >> 配件 系列:- 標準包裝:100 系列:- 其它名稱:886.0007886.0007-ND |
| 8Y1011-Z | 功能描述:SWITCH PUSHBUTTON SPDT 6A 125V RoHS:是 類別:開關 >> 按鈕 系列:8Y 標準包裝:1 系列:A16 類型:標準，發光式 電路:雙刀雙擲 開關功能:開-瞬時 額定電流:5A（AC） 額定電壓 - AC:125V 額定電壓 - DC:- 觸動器類型:方形，按鈕 顏色 - 致動器/蓋:黃 發光類型，顏色:LED，黃 發光電壓:12 VDC 安裝類型:前面板安裝 端接類型:焊接，快速連接 - 0.110"（2.8mm） 防護等級:IP65 - 防塵/防油/防水 特點:- 面板切口尺寸:圓形 - 直徑 16.00mm 包裝:散裝 工作溫度:-10°C ~ 55°C 機械壽命:2,000,000 次循環 電氣壽命:100,000 次循環 其它名稱:A165LAYM12D2 |
發布緊急采購，3分鐘左右您將得到回復。