- 您現在的位置：買賣IC網 > PDF目錄364548 > 89C535 (NXP Semiconductors N.V.) CMOS single-chip 8-bit microcontrollers with FLASH program memory PDF資料下載
參數資料
| 型號： | 89C535 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | CMOS single-chip 8-bit microcontrollers with FLASH program memory |
| 中文描述： | CMOS單芯片8位微控制器的FLASH程序存儲器 |
| 文件頁數： | 26/35頁 |
| 文件大?。?/td> | 221K |
| 代理商： | 89C535 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Philips Semiconductors
Preliminary specification
89C535/89C536/89C538
CMOS single-chip 8-bit microcontrollers
with FLASH program memory
1997 Jun 05
26
System Considerations
During the switch between active and standby conditions, transient
current peaks are produced on the rising and falling edges of Chip
Enable. The magnitude of these transient current peaks is
dependent on the output capacitance loading of the device. At a
minimum, a 0.1uF ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between V
CC
and GND,
and between V
PP
and GND to minimize transient effects.
SYMBOL
PARAMETER
MIN
TYP
MAX
UNIT
CONDITION
C
IN
C
OUT
V
PPH
V
PPH
14
PF
VI
N
= 0V
V
OUT
= 0V
16
pF
Command programming/Data programming/Erase Operation
DC CHARACTERISTICS
T
amb
= 0
°
C to 70
°
C, V
CC
= 5V
±
10%, V
PP
= 12.0V
±
5%
SYMBOL
PARAMETER
CONDITION
MIN
TYP
MAX
UNIT
I
LI
Input Leakage Current
V
IN
= GND to V
CC
10
μ
A
I
LO
Output Leakage Current
V
OUT
= GND to V
CC
10
μ
A
I
SB1
I
SB2
Standby V
CC
Current
CE = VI
H
1
mA
CE = V
CC
±
0.3 V
1
100
μ
A
I
CC1
(Read)
Operating V
CC
Current
I
OUT
= 0 mA, f=1 MHz
30
mA
I
CC2
I
OUT
= 0 mA, F=11MHz
50
mA
I
CC3
(Program)
In Programming
50
mA
I
CC4
(Erase)
In Erase
50
mA
I
CC5
(Program Verify)
In Program Verify
50
mA
I
CC6
(Erase Verify)
In erase Verify
50
mA
I
PP1
(Read)
V
PP
Current
V
PP
=12.6 V
100
μ
A
I
PP2
(Program)
In Programming
50
mA
I
PP3
(Erase)
In Erase
50
mA
I
PP4
(Program Verify)
In Program Verify
50
mA
I
PP5
(Erase Verify)
In Erase Verify
50
mA
V
IL
Input Voltage
–0.5 (Note 5)
0.2V
PP
– 0.3
V
V
IH
2.4
V
CC
+0.3V
V
(Note 6)
V
OL
Output Voltage Low
I
OL
=2.1mA
0.45
V
V
OH
NOTES:
1. V
CC
must be applied before V
PP
and removed after V
PP
.
2. V
must not exceed 14V including overshoot.
3. An influence may be had upon device reliability if the device is installed or removed while V
PP
=12V.
4. Do not alter V
from V
to 12V or 12V to V
IL
when CE=V
IL
5. V
IL
min. = –0.5V for pulse width
≤
20ns.
6. If V
is over the specified maximum value, programming operation cannot be guaranteed.
7. All currents are in RMS unless otherwise noted. (Sampled, not 100% tested.).
Output Voltage High
I
OH
=400uA
2.4
V
相關PDF資料 |
PDF描述 |
|---|---|
| 89C54 | 80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
| 89C51 | 80C51 8-bit microcontroller family 4K Flash(80C51八位微控制器系列 4K 閃速存儲器) |
| 89C52 | 80C51 8-bit microcontroller family8KFlash(80C51八位微控制器系列 8K閃速存儲器) |
| 89C58 | 80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
| 89CNQ135 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 89C536 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 16K/64K/512 FLASH |
| 89C538 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers with FLASH program memory |
| 89C54 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
| 89C55 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 20K Bytes Flash |
| 89C58 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller family 4K/8K/16K/32K Flash |
發布緊急采購，3分鐘左右您將得到回復。