- 您現在的位置：買賣IC網 > PDF目錄364522 > 8547TS (NXP Semiconductors N.V.) 2 x 0.7 W BTL audio amplifier with output channel switching PDF資料下載
參數資料
| 型號： | 8547TS |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 音頻放大器 |
| 英文描述： | 2 x 0.7 W BTL audio amplifier with output channel switching |
| 中文描述： | 2 × 0.7糯橋接音頻放大器的輸出開關通道 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 162K |
| 代理商： | 8547TS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
1998 Apr 01
9
Philips Semiconductors
Product specification
2
×
0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
TEST AND APPLICATION INFORMATION
Test conditions
Because the application can be either Bridge-Tied Load
(BTL) or Single-Ended (SE), the curves of each
application are shown separately.
The thermal resistance = 110 K/W for the SSOP20; the
maximum sine wave power dissipation for T
amb
= 25
°
C
25
–
110
is:
For T
amb
= 60
°
C the maximum total power dissipation is:
60
–
110
Thermal Design Considerations
The ‘measured’ thermal resistance of the IC package is
highly dependent on the configuration and size of the
application board. Data may not be comparable between
different Semiconductor manufacturers because the
application boards and test methods are not (yet)
standardized. Also, the thermal performance of packages
for a specific application may be different than presented
here, because the configuration of the application boards
(copper area!) may be different. Philips Semiconductors
uses FR-4 type application boards with 1 oz copper
traces with solder coating.
The SSOP package has improved thermal conductivity
which reduces the thermal resistance. Using a practical
PCB layout (see Fig.24) with wider copper tracks to the
corner pins and just under the IC, the thermal resistance
from junction to ambient can be reduced to about 80 K/W.
For T
amb
= 60
°
C the maximum total power dissipation at
60
–
80
this PCB layout is:
Please note that this two channel IC is mentioned for
application with only one channel active. For that reason
the curves for worst case power dissipation are given for
the condition of only one of the both channels driven with
a 1 kHz sine wave signal.
BTL application
T
amb
= 25
°
C if not specially mentioned, V
CC
= 5 V,
f = 1 kHz, R
L
= 8
, G
v
= 20 dB, audio band-pass
22 Hz to 22 kHz.
The BTL application circuit is illustrated in Fig.4.
150
1.14 W
=
150
0.82 W
=
150
1.12 W
=
The quiescent current has been measured without any
load impedance and both channels driven. When one
channel is active the quiescent current will be halved.
The total harmonic distortion as a function of frequency
was measured using a low-pass filter of 80 kHz.
The value of capacitor C3 influences the behaviour of the
SVRR at low frequencies: increasing the value of C3
increases the performance of the SVRR.
The figure of the MODE voltage (V
MODE
) as a function of
the supply voltage shows three areas; operating, mute
and standby. It shows, that the DC-switching levels of the
mute and standby respectively depend on the supply
voltage level. The figure of the SELECT voltage (V
SELECT
)
as a function of the supply voltage shows the voltage
levels for switching the channels in the active, mute or
standby mode.
SE application
T
amb
= 25
°
C if not specially mentioned, V
CC
= 7.5 V,
f = 1 kHz, R
L
= 4
, G
v
= 20 dB, audio band-pass
22 Hz to 22 kHz.
The SE application circuit is illustrated in Fig.16.
Increasing the value of electrolytic capacitor C3 will result
in a better channel separation. Because the positive
output is not designed for high output current (2
×
I
o
) at
low load impedance (
≤
16
), the SE application with
output capacitors connected to ground is advised.
The capacitor value of C6/C7 in combination with the load
impedance determines the low frequency behaviour.
The THD as a function of frequency was measured using
a low-pass filter of 80 kHz. The value of capacitor C3
influences the behaviour of the SVRR at low frequencies:
increasing the value of C3 increases the performance of
the SVRR.
General remark
The frequency characteristic can be adapted by
connecting a small capacitor across the feedback
resistor. To improve the immunity to HF radiation in radio
circuit applications, a small capacitor can be connected in
parallel with the feedback resistor (56 k
); this creates a
low-pass filter.
相關PDF資料 |
PDF描述 |
|---|---|
| 854909 | Analog Filter |
| 854917 | Analog Filter |
| 854919 | Analog Filter |
| 854913 | Analog Filter |
| 854920 | Analog Filter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 8548 | 制造商:Abbatron/HH Smith 功能描述:Spacer; Round; Aluminum; #10 ID; 5/16" OD; 1 1/4" Length |
| 85480 | 制造商:Brady Corporation 功能描述:GLOW-IN-THE-DARK PLASTIC SIGN |
| 85-480 | 制造商:Ideal Industries Inc 功能描述:BNC 59 TWIST-ON 1PC DCAST PVC |
| 854-80-009-10-001101 | 制造商:PRECI-DIP 功能描述:PCB CONN SOLDER TAIL 1.27MM |
| 854-80-009-20-001101 | 制造商:PRECI-DIP 功能描述:PCB CONN SOLDER TAIL 1.27MM |
發布緊急采購，3分鐘左右您將得到回復。