- 您現在的位置：買賣IC網 > PDF目錄378217 > 82802AB (Intel Corp.) Firmware Hub (FWH) PDF資料下載
參數資料
| 型號： | 82802AB |
| 廠商： | Intel Corp. |
| 英文描述： | Firmware Hub (FWH) |
| 中文描述： | 固件集線器（固件樞紐） |
| 文件頁數： | 22/53頁 |
| 文件大?。?/td> | 471K |
| 代理商： | 82802AB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Intel
82802AB/AC Firmware Hub
R
22
Datasheet
4.5.
Block Erase Command
The erase command operates on one block at a time. This command requires an (arbitrary) address
within the block to be erased. Recall that erasure changes all block data to FFh. Block preconditioning,
erase, and erase verify are handled internally by the WSM, which is transparent to the system. After
issuing the erase command, the device automatically outputs status register data when read. When the
block erase completes, the status register may be checked. If the FWH detects a block erase error, the
status register should be cleared before system software attempts corrective actions. After a block erase,
the CUI remains in read status register mode until a new command is issued.
Successful block erasure requires that the corresponding block’s write-lock-bit is cleared, and the
corresponding write-protect pin (TBL# or WP#) is inactive. If a block erase is attempted when the block
is locked, the block erase will fail, with the reason for failure in the status register.
Successful block erase only occurs when V
PP
= V
PPH1
or V
PPH2
. If the erase operation is attempted at
V
PP
≠
V
PPH1
or V
PPH2
, erratic results may occur.
4.6.
Program Command
Program command operates on one byte at a time. This command specifies the address and data to be
programmed. After the CUI receives the command, the WSM takes over, controlling the program and
verify algorithms internally. After the program command is written, the device automatically outputs the
status register data when read. When programming is complete, the status register may be checked. If a
program error is detected, the status register should be cleared before corrective action is taken by the
software. The internal WSM verification error checking only detects 1s that does not successfully
program to 0s. The CUI remains in
read status register mode
until it receives another command.
Reliable programming only occurs when V
PP
= V
PPH1
or V
PPH2
. If programming is attempted at
V
PP
≠
V
PPH1
or V
PPH2
, erratic results may occur.
Successful program operation also requires that the corresponding block’s write-lock bit be cleared and
that the corresponding write-protect pin (TBL# or WP#) be inactive. If program operation is attempted
when the block is locked, the operation will fail.
相關PDF資料 |
PDF描述 |
|---|---|
| 82802AC | Firmware Hub (FWH) |
| 8281 | LNB SUPPLY AND CONTROL-VOLTAGE REGULATORS |
| 8282 | OCTAL LATCH |
| 8282 | LNB SUPPLY AND CONTROL-VOLTAGE REGULATORS |
| 82845G | Intel 82845G/82845GL/82845GV Graphics and Memory Controller Hub (GMCH) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 82802AC | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Firmware Hub (FWH) |
| 82802D | 功能描述:ADPTR LRG HEX DIE 1/2DR 制造商:apex tool group 系列:* 零件狀態:在售 標準包裝:6 |
| 8280-2PG-311 | 功能描述:標準環形連接器 MINI-CON CBL-CBL #20 CRIMP RoHS:否 制造商:Hirose Connector 系列:EM-W 產品類型:Accessories 位置/觸點數量:1 觸點類型: 觸點電鍍: 安裝風格:Cable 外殼材質: 端接類型:Clamp 電壓額定值: |
| 8280-2PG-315 | 功能描述:標準環形連接器 MINI-CON CBL-CBL #20 CRIMP RoHS:否 制造商:Hirose Connector 系列:EM-W 產品類型:Accessories 位置/觸點數量:1 觸點類型: 觸點電鍍: 安裝風格:Cable 外殼材質: 端接類型:Clamp 電壓額定值: |
| 8280-2PG-318 | 功能描述:標準環形連接器 MINI-CON CBL-CBL #20 CRIMP RoHS:否 制造商:Hirose Connector 系列:EM-W 產品類型:Accessories 位置/觸點數量:1 觸點類型: 觸點電鍍: 安裝風格:Cable 外殼材質: 端接類型:Clamp 電壓額定值: |
發布緊急采購，3分鐘左右您將得到回復。