• 參數資料
    型號: 7P016FLA6502C15
    英文描述: MCU CMOS 28LD 40MHZ 12K FLASH, -40C to +85C, 28-SOIC 300mil, T/R
    中文描述: 周邊雜項
    文件頁數: 10/15頁
    文件大?。?/td> 140K
    代理商: 7P016FLA6502C15
    August 2000 Rev. 4 - ECO #13125
    4
    PCMCIA Flash Memory Card
    FLA Series
    PC Card Products
    Symbol
    Type
    Name and Function
    A0 - A25
    INPUT
    ADDRESS INPUTS: A0 through A25 enable direct addressing of up to
    64MB of memory on the card. Signal A0 is not used in word access
    mode. A25 is the most significant bit
    DQ0 - DQ15
    INPUT/OUTPUT
    DATA INPUT/OUTPUT: DQ0 THROUGH DQ15 constitute the bi-
    directional databus. DQ15 is the MSB.
    CE1#, CE2#
    INPUT
    CARD ENABLE 1 AND 2: CE1# enables even byte accesses, CE2#
    enables odd byte accesses. Multiplexing A0, CE1# and CE2# allows 8-
    bit hosts to access all data on DQ0 - DQ7.
    OE#
    INPUT
    OUTPUT ENABLE: Active low signal gating read data from the
    memory card.
    WE#
    INPUT
    WRITE ENABLE: Active low signal gating write data to the memory
    card.
    RDY/BSY#
    OUTPUT
    READY/BUSY OUTPUT: Indicates status of internally timed erase or
    program algorithms. A high output indicates that the card is ready to
    accept accesses. A low output indicates that one or more devices in the
    memory card are busy with internally timed erase or write activities.
    CD1#, CD2#
    OUTPUT
    CARD DETECT 1 and 2: Provide card insertion detection. These
    signals are internally connected to ground on the card. The host shall
    monitor these signals to detect card insertion (pulled-up on host side).
    WP
    OUTPUT
    WRITE PROTECT: Write protect reflects the status of the Write Protect
    switch on the memory card. WP set to high = write protected, providing
    internal hardware write lockout to the Flash array.
    If card does not include optional write protect switch, this signal will be
    pulled low internally indicating write protect = "off".
    VPP1, VPP2
    N.C.
    PROGRAM/ERASE POWER SUPPLY: Provides programming
    voltages for card (12V). Not connected for 5V only card.
    VCC
    CARD POWER SUPPLY: (5.0V).
    GND
    CARD GROUND
    REG#
    INPUT
    ATTRIBUTE MEMORY SELECT : Active low signal, enables access to
    Attribute Memory Plane, occupied by Card Information Structure and
    Card Registers.
    RST
    INPUT
    RESET: Active high signal for placing card in Power-on default state.
    Reset can be used as a Power-Down signal for the memory array.
    WAIT#
    OUTPUT
    WAIT: This signal is pulled high internally for compatibility. No wait
    states are generated.
    BVD1, BVD2
    OUTPUT
    BATTERY VOLTAGE DETECT: These signals are pulled high to
    maintain SRAM card compatibility.
    VS1, VS2
    OUTPUT
    VOLTAGE SENSE: Notifies the host socket of the card's VCC
    requirements. VS1 and VS2 are open to indicate a 5V card .
    RFU
    RESERVED FOR FUTURE USE
    N.C.
    NO INTERNAL CONNECTION TO CARD: pin may be driven or left
    floating
    Card Signal Description
    READ function
    Common Memory
    Attribute Memory
    Function Mode
    /CE2
    /CE1
    A0
    /OE
    /WE
    /REG
    D15-D8
    D7-D0
    /REG
    D15-D8
    D7-D0
    Standby Mode
    H
    X
    High-Z
    X
    High-Z
    Byte Access (8 bits)
    H
    L
    H
    High-Z
    Even-Byte
    L
    High-Z
    Even-Byte
    HL
    H
    High-Z
    Odd-Byte
    LHigh-Z
    Not Valid
    Word Access (16 bits)
    L
    X
    L
    H
    Odd-Byte Even-Byte
    L
    Not Valid
    Even-Byte
    Odd-Byte Only Access
    L
    H
    X
    L
    H
    Odd-Byte
    High-Z
    L
    Not Valid
    High-Z
    WRITE function
    Standby Mode
    H
    X
    XX
    X
    XX
    X
    Byte Access (8 bits)
    HL
    L
    H
    L
    H
    X
    Even-Byte
    L
    X
    Even-Byte
    HL
    H
    L
    H
    X
    Odd-Byte
    LX
    X
    Word Access (16 bits)
    L
    X
    H
    L
    H
    Odd-Byte Even-Byte
    L
    X
    Even-Byte
    Odd-Byte Only Access
    L
    H
    X
    H
    L
    H
    Odd-Byte
    X
    LX
    X
    Functional Truth Table
    相關PDF資料
    PDF描述
    7P016FLB2202I15 EEPROM
    7P016FLB2300C15 EEPROM
    7P016FLB2300I15 EEPROM
    7P016FLB2301C15 EEPROM
    7P016FLB2301I15 EEPROM
    相關代理商/技術參數
    參數描述
    7P-10.000MBP-T 功能描述:OSC TCXO 10.000MHZ CMOS SMD 制造商:txc corporation 系列:* 零件狀態:在售 標準包裝:1,000
    7P102V330A052 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum
    7P102V330N042 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum
    7P102V360A052 功能描述:鋁質電解電容器-管理單元 1000uF 360V PHOTO RoHS:否 制造商:Nichicon 電容:470 uF 容差:20 % 電壓額定值:450 V ESR: 工作溫度范圍:- 25 C to + 105 C 系列:AR 直徑:35 mm 長度:45 mm 引線間隔:10 mm 產品:General Purpose Electrolytic Capacitors
    7P122V330A052 制造商:CDE 制造商全稱:Cornell Dubilier Electronics 功能描述:Type 7P 55 ∑C Photoflash, High-Energy, Long Life, Aluminum