參數資料
型號： 78M6618-IM/F/P
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, QCC68
封裝： 8 X 8 MM, ROHS COMPLIANT, TQFN-68
文件頁數： 2/32頁
文件大?。?/td> 419K
代理商： 78M6618-IM/F/P
78M6618 Data Sheet
DS_6618_005
10
Rev. 1.4
V3P3
V3P3 -
400mV
V3P3 - 10mV
VBIAS
0V
Battery
modes
Normal
operation,
WDT
enabled
WDT dis-
abled
V1
1.12 Real-Time Clock (RTC)
The RTC circuit is driven directly by the crystal oscillator. The RTC consists of a counter chain and output
registers. The counter chain consists of registers for seconds, minutes, hours, day of week, day of
month, month, and year (including leap years). See the 78M6618 Programmer’s Reference Manual for
more information regarding the use of the 78M6618 RTC.
1.13 Hardware Watchdog Timer
In addition to the basic watchdog timer included in the 80515 MPU, an
independent, robust, fixed-duration, watchdog timer (WDT) is included in
the device. It uses the crystal oscillator as its time base and must be
refreshed by the MPU firmware at least every 1.5 seconds. When not
refreshed on time the WDT overflows, and the part is reset as if the RESET
pin were pulled high, except that the IORAM bits will be maintained. 4096
oscillator cycles (or 125 ms) after the WDT overflow, the MPU will be
launched from program address 0x0000. Asserting ICE_E will deactivate
the WDT.
The WDT can also be disabled by tying the V1 pin to V3P3. This also
deactivates V1 power fault detection. Since there is no method in firmware
to disable the crystal oscillator or the WDT, it is guaranteed that whatever
state the part might find itself in, upon watchdog overflow, the part will be
reset to a known state.
Figure 3: Functions Defined by V1
1.14 Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap re-
ference. The primary use of the temperature data is to determine the magnitude of compensation required
to offset the thermal drift in the system. See the 78M6618 Programmer’s Reference Manual for more
information regarding the use of the 78M6618 Temperature Sensor.
1.15 General Purpose Digital I/O
The 78M6618 includes up to 19 pins of general-purpose digital I/O. When configured as inputs, these
pins are 5V compatible (no current-limiting resistors are needed).
On reset or power-up, all DIO pins are
inputs until they are configured for the desired direction under MPU control. The Digital I/O pins can be
categorized as follows:
DIO1/OPT_RX, DIO2/OPT_TX
(2 pins) UART/DIO pin
DIO3
(1 pin ) Dedicated DIO pin
DIO4/SEG24
-- DIO11/SEG31
(8 pins) LCD/DIO pins
DIO13/SEG33 -- DIO19/SEG39
(7 pins) LCD/DIO pins
DIO43/SEG63
(1 pin ) LCD/DIO pin
相關PDF資料
PDF描述
78M6618-IMR/F/P SPECIALTY ANALOG CIRCUIT, QCC68
7MBP150RTJ060 AC MOTOR CONTROLLER, 300 A, XMA25
7MBP25RU2A120 AC MOTOR CONTROLLER, 50 A, XMA22
7MBP50RTJ060 AC MOTOR CONTROLLER, 100 A, XMA25
7MBP50RU2A120 AC MOTOR CONTROLLER, 100 A, XMA22
相關代理商/技術參數
參數描述
78M6618-IMR 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Octal Power and Energy Measurement IC
78M6618-IMR/F 功能描述:計量片上系統 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
78M6618-IMR/F/P 制造商:Maxim Integrated Products 功能描述:PROGRAMMED - LEAD FREE/TAPE & REEL - Tape and Reel
78M6618-IMR/F/PB1 制造商:Maxim Integrated Products 功能描述:- Tape and Reel
78M6618-IMR/F1 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*