- 您現在的位置：買賣IC網 > PDF目錄8060 > 74HC191DB,118 (NXP Semiconductors)IC 4BIT BINAR UP/DN COUNT 16SSOP PDF資料下載
參數資料
| 型號： | 74HC191DB,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 4BIT BINAR UP/DN COUNT 16SSOP |
| 產品培訓模塊： | Logic Packages |
| 標準包裝： | 2,000 |
| 系列： | 74HC |
| 邏輯類型： | 二進制計數器 |
| 方向： | 上，下 |
| 元件數： | 1 |
| 每個元件的位元數： | 4 |
| 計時： | 同步 |
| 計數速率： | 39MHz |
| 觸發器類型： | 正邊沿 |
| 電源電壓： | 2 V ~ 6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 74HC191DB-T 74HC191DB-T-ND 935188600118 |
December 1990
2
Philips Semiconductors
Product specication
Presettable synchronous 4-bit binary
up/down counter
74HC/HCT191
FEATURES
Synchronous reversible counting
Asynchronous parallel load
Count enable control for synchronous expansion
Single up/down control input
Output capability: standard
ICC category: MSI
GENERAL DESCRIPTION
The 74HC/HCT191 are high-speed Si-gate CMOS devices
and are pin compatible with low power Schottky TTL
(LSTTL). They are specified in compliance with JEDEC
standard no. 7A.
The 74HC/HCT191 are asynchronously presettable 4-bit
binary up/down counters. They contain four master/slave
flip-flops with internal gating and steering logic to provide
asynchronous preset and synchronous count-up and
count-down operation.
Asynchronous parallel load capability permits the counter
to be preset to any desired number. Information present on
the parallel data inputs (D0 to D3) is loaded into the counter
and appears on the outputs when the parallel load (PL)
input is LOW. As indicated in the function table, this
operation overrides the counting function.
Counting is inhibited by a HIGH level on the count enable
(CE) input. When CE is LOW internal state changes are
initiated synchronously by the LOW-to-HIGH transition of
the clock input. The up/down (U/D) input signal determines
the direction of counting as indicated in the function table.
The CE input may go LOW when the clock is in either
state, however, the LOW-to-HIGH CE transition must
occur only when the clock is HIGH. Also, the U/D input
should be changed only when either CE or CP is HIGH.
Overflow/underflow indications are provided by two types
of outputs, the terminal count (TC) and ripple clock (RC).
The TC output is normally LOW and goes HIGH when a
circuit reaches zero in the count-down mode or reaches
“15” in the count-up-mode. The TC output will remain
HIGH until a state change occurs, either by counting or
presetting, or until U/D is changed. Do not use the TC
output as a clock signal because it is subject to decoding
spikes. The TC signal is used internally to enable the
RC output. When TC is HIGH and CE is LOW, the RC
output follows the clock pulse (CP). This feature simplifies
the design of multistage counters as shown in Figs 5
and 6.
In Fig.5, each RC output is used as the clock input to the
next higher stage. It is only necessary to inhibit the first
stage to prevent counting in all stages, since a HIGH on
CE inhibits the RC output pulse as indicated in the function
table. The timing skew between state changes in the first
and last stages is represented by the cumulative delay of
the clock as it ripples through the preceding stages. This
can be a disadvantage of this configuration in some
applications.
Fig.6 shows a method of causing state changes to occur
simultaneously in all stages. The RC outputs propagate
the carry/borrow signals in ripple fashion and all clock
inputs are driven in parallel. In this configuration the
duration of the clock LOW state must be long enough to
allow the negative-going edge of the carry/borrow signal to
ripple through to the last stage before the clock goes
HIGH. Since the RC output of any package goes HIGH
shortly after its CP input goes HIGH there is no such
restriction on the HIGH-state duration of the clock.
In Fig.7, the configuration shown avoids ripple delays and
their associated restrictions. Combining the TC signals
from all the preceding stages forms the CE input for a
given stage. An enable must be included in each carry
gate in order to inhibit counting. The TC output of a given
stage it not affected by its own CE signal therefore the
simple inhibit scheme of Figs 5 and 6 does not apply.
相關PDF資料 |
PDF描述 |
|---|---|
| 74LCX245SJ | IC TRANSCVR BIDIR 8BIT 20SOP |
| 74LVTH2244MTC | IC BUFF/DVR TRI-ST DUAL 20TSSOP |
| 74HC93DB,118 | IC 4BIT BINARY RIPPLE 14SSOP |
| 74LVT2244MTC | IC BUFF/DVR TRI-ST DUAL 20TSSOP |
| 74HCT4060DB,118 | IC 14STAGE BINARY RIPPLE 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74HC191DB-T | 功能描述:計數器 IC SYNC BIN U/D COUNTER RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel |
| 74HC191D-T | 功能描述:計數器 IC SYNC BIN U/D COUNTER RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel |
| 74HC191E | 制造商:undefined 功能描述: |
| 74HC191N | 制造商:NXP Semiconductors 功能描述:HC Counter Bulk 制造商:NXP Semiconductors 功能描述:IC 74HC CMOS 74HC191 DIP16 5V 制造商:NXP Semiconductors 功能描述:IC, 74HC CMOS, 74HC191, DIP16, 5V 制造商:NXP Semiconductors 功能描述:BINARY COUNTER, 4BIT, UP/DOWN, DIP-16; Counter Type:Presettable Binary, Synchronous, Up / Down; Clock Frequency:39MHz; Count Maximum:15; Supply Voltage Min:2V; Supply Voltage Max:6V; Logic Case Style:DIP; No. of Pins:16 ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:4-bit binary up/down counter,74HC191N 制造商:NXP Semiconductors 功能描述:Counter Single 4-Bit Sync Binary UP/Down 16-Pin PDIP Bulk |
| 74HC191N,652 | 功能描述:計數器 IC COUNTER UP/DOWN SYNC RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。