- 您現在的位置：買賣IC網 > PDF目錄68813 > 73S8024RN-20IM (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC20 PDF資料下載
參數資料
| 型號： | 73S8024RN-20IM |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 封裝： | 4 X 4 MM, 0.850 MM HEIGHT, QFN-20 |
| 文件頁數： | 23/23頁 |
| 文件大?。?/td> | 318K |
| 代理商： | 73S8024RN-20IM |
73S8024RN
Low Cost Smart Card Interface
DATA SHEET
Page: 9 of 23
2005 TERIDIAN Semiconductor Corporation
Rev 1.5
DEACTIVATION SEQUENCE
Deactivation is initiated either by the system controller by setting the
CMDVCC high, or automatically in the event
of hardware faults. Hardware faults are over-current, overheating, VDD fault, VPC fault, VCC fault, and card
extraction during the session. To be noted that VPC and VCC faults are linked together so that a fault is generated
when VPC goes lower than VCC.
The following steps show the deactivation sequence and the timing of the card control signals when the system
controller sets the
CMDVCC high or OFF goes low due to a fault or card removal:
-
RST goes low at the end of t1.
-
CLK is set low at the end of t2.
-
I/O goes low at the end of t3. Out of reception mode.
-
VCC is shut down at the end of time t4. After a delay t5 (discharge of the VCC capacitor), VCC is low.
RST
CLK
I/O
VCC
t
1
t
2
t
3
t
4
t
5
CMDVCC
-- OR--
OFF
t1 = > 0.5s, timing by 1.5MHZ internal Oscillator
t2 = > 7.5s
t3 = > 0.5s
t4 = > 0.5s
t5 = depends on VCC filter capacitor.
For NDS application, CF=1F makes t1 + t2 + t3 + t4 + t5 < 100s
Figure 4: Deactivation Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| 73S8024RN-32IMR | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8024RN-32IM | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8024RN-20IMR | SPECIALTY ANALOG CIRCUIT, QCC20 |
| 74ACT715L | SPECIALTY CONSUMER CIRCUIT, CQCC20 |
| 74ACT715LX | SPECIALTY CONSUMER CIRCUIT, CQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8024RN-20IM/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-20IM/F1 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-20IMR/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-20IMR/F1 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-32IM/F | 功能描述:IC SMART CARD INTERFACE 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。