- 您現在的位置：買賣IC網 > PDF目錄10922 > 73S1210F-44IM/F (Maxim Integrated Products)IC SMART CARD READER 44-QFN PDF資料下載
參數資料
| 型號： | 73S1210F-44IM/F |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 46/126頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SMART CARD READER 44-QFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 260 |
| 系列： | 73S12xx |
| 核心處理器： | 80515 |
| 芯體尺寸： | 8-位 |
| 速度： | 24MHz |
| 連通性： | I²C，智能卡，UART/USART |
| 外圍設備： | LED，POR，WDT |
| 輸入/輸出數： | 8 |
| 程序存儲器容量： | 32KB（32K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 6.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-VFQFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
73S1210F Data Sheet
DS_1210F_001
26
Rev. 1.4
VBAT is expected to be supplied from a battery of three to four series connected cells with a voltage value
of 4.0 to 6.5 volts.
VBAT and VBUS are internally switched to VPC by two separate FET switches configured as a SPDT switch
(break-before-make). They will not be enabled at the same time. VBUS is automatically selected in lieu of
VBAT when VBUS is present (i.e. VBUS always has the priority).
If VPC is provided and either VBAT or VBUS is also used, the source of VPC must be diode isolated from the
VPC pin to prevent current flow from VBAT or VBUS into the VPC source.
The power that is supplied to the VPC pin (externally or internally, i.e. through VBAT or VBUS – see above) is
up-converted to the intermediate voltage VP utilizing an inductive, step-up converter. A series power
inductor (nominal value = 10
H) must be connected from V
PC to the pin LIN, and a 10F low ESR filter
capacitor must be connected to VPC.
VP requires a 4.7F filter capacitor and will have a nominal value of 5.5 volts during normal operation. VP
is used internally by the smart card electrical interface circuit and is regulated to the desired smart card
supply VCC voltage (can be programmed for values of 5V, 3V, or 1.8V).
VP is also used internally to generate a 3.3V nominal, regulated power supply VDD. VDD is output on pin
68 and must be directly tied to all other VDD pins on the 73S1210F (pins 28 and 40). VDD powers all the
digital logic, input/output buffering, and analog functions. It can also be used for external circuitry: up to
20mA current can be supplied to external devices simultaneously to the 73S1210F’s digital core
maximum consumption.
1.7.3
Power ON/OFF
The 73S1210F features an ON_OFF input pin for a momentary contact, main-system ON/OFF switch. The
purpose of this switch is to place the circuit in a very low-power mode – the “OFF” mode – where all circuits
are no longer powered, therefore allowing the lowest possible current consumption.
When in “OFF” mode, an action on the ON/OFF switch will turn-on the power supply of the digital core
(VDD) and apply a power-on-reset condition. Alternatively, entering the “OFF” mode from the “ON” mode
requires firmware action.
When in “ON” mode, an action on the ON/OFF switch will send a request to the controller that will have to
be acknowledged (firmware action required) in order to enter the “OFF” state.
When placed into the “OFF” state, the 73S1210F will consume minimum current from VPC and VBAT; VP
and VDD will be unavailable (VDD out = 0V and VP = 0V).
When in “ON” mode, the 73S1210F will operate normally, with all the features described in this document
available. VP and VDD will be available (VDD out = 3.3V and VP = 5.5V nominal).
Whenever VBUS power is supplied, the circuit will be automatically in the “ON” state. The functions of the
ON/OFF switch and circuitry are overridden and the 73S1210F is in the “ON” state with VP and VDD available.
Without VBUS applied, the circuit is by default in the “OFF” state, and will respond only to the ON_OFF pin.
The ON_OFF pin should be connected to an SPST switch to ground. If the circuit is OFF and the switch
is closed for a debounce period of 50-100ms, the circuit will go into the “ON” state wherein all functions
are operating in normal fashion. If the circuit is in the “ON” state and the ON/OFF pin is connected to
ground for a period greater than the debounce period, OFF_REQ will be asserted high and held
regardless of the state of ON/OFF. The OFF_REQ signal should be connected to one of the interrupt
pins to signal the CPU core that a request to shutdown has been initiated. The firmware will
acknowledge this request by setting the SCPWRDN bit in the Smart Card VCC Control/Status Register
(VccCtl) high after it has completed all shutdown activities. When SCPWRDN is set high, the circuit will
deactivate the smart card interface if required and turn off all analog functions and the VDD supply for the
logic and companion circuits. The default state upon application of power is the “OFF” state unless
power is supplied to the VBUS supply. Note that at any time, the firmware may assert SCPWRDN and the
相關PDF資料 |
PDF描述 |
|---|---|
| ISD17150EYI | IC VOICE REC/PLAY 150SEC 28-TSOP |
| VE-26J-CV-S | CONVERTER MOD DC/DC 36V 150W |
| ISD17210EY | IC VOICE REC/PLAY 210SEC 28-TSOP |
| ISD1790SYI | IC VOICE REC/PLAY 90-SEC 28-SOIC |
| ISD1790PYI | IC VOICE REC/PLAY 90-SEC 28-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S1210F-44IMR/F | 功能描述:8位微控制器 -MCU SoC Smart Card Readr w/PINpad & PWR Mgt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| 73S1210F-44IMR/F/P | 功能描述:IC SMART CARD READER PROG 44-QFN RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:73S12xx 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| 73S1210F-44M/F/PC | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| 73S1210F-44M/F/PD | 制造商:Maxim Integrated Products 功能描述:SCR+PIN PAD/SRL INTRFC/PWR MGT-PROG - Rail/Tube |
| 73S1210F-44MR/F/PC | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。