參數資料
| 型號： | 73628 |
| 廠商： | Desco |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 0K |
| 描述： | COAT LAB W/SNAPS WHITE 5XLARGE |
| 標準包裝： | 1 |
| 系列： | Statshield® |
| 服裝類型： | 實驗室罩衣，帶按扣 |
| 尺寸： | 5XLarge |
| 材質： | 聚酯 |
| 顏色： | 白 |
| 特點： | 袖口帶 4mm 卡扣式插口，胯部帶 4mm 卡釘 |
Installation
Follow the directions below for proper installation and
grounding of the Statshield smock.
1. Put on the smock and fasten all of the snaps on the front
of the smock, making sure that clothing is not exposed
outside of the smock.
2. Throughout use, it is essential that conductive cuff (or the
wristband) be in contact with operator’s skin; the
conductive cuff (or the wristband) should never be
allowed to be pulled up and over shirt sleeve.
3. Install a coil cord to the snap stud located above the left
hand hip pocket. Connect the other end of the coil cord
to a verified ground point or continuous monitor.
Grounding Integrity Testing
For daily testing or continuous monitoring of the grounding
integrity of Statshield smocks and ground cords, we
recommend testing the smock while worn and the use of
a standard wrist strap testers or single-wire workstation
continuous monitors. Panel-to-panel conductivity is essential
so as not to leave portions of the smock as isolated charged
conductors. Panel-to-panel conductivity is easy to test using
our Surface Resistance Meter Kit Item #
19787. Place the
two five-pound electrodes on different panels to test. Unless
properly grounded, the smocks can hold a charge and
become a possible source for discharge to ESD sensitive
items. For additional information, refer to ANSI/ESD S20.20,
ESD TR20.20, ESD TR53 and the Garment Standard,
ANSI/ESD STM2.1. Desco has several testers available
for this purpose. For more information ask for specification
drawings or operating instruction manuals by item number.
TB-2055 Page 3 of 4
2013 DESCO INDUSTRIES INC.
Employee Owned
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
Figure 5. Testing and monitoring of smock and ground
cord assembly
YES!
NO!
Figure 3. Proper installation of smock wearer’s body
Figure 4. Grounding the smock
Figure 6. Testers
NOTE: ANSI/ESD S20.20 RECOMMENDS THAT THE
GROUND COIL CORD SELECTED FOR GROUNDING OF
PERSONNEL CONTAIN A BUILT-IN CURRENT LIMITING
1 MEGOHM RESISTOR.
Heat Sealed Patches
It is possible to heat seal patches to our smocks. The patch
should be small and the smock should be tested before and
after application.
相關PDF資料 |
PDF描述 |
|---|---|
| 73627 | COAT LAB W/SNAPS WHITE 4XLARGE |
| 73626 | COAT LAB W/SNAPS WHITE 3XLARGE |
| 73620 | COAT LAB W/SNAPS WHITE XSMALL |
| 73619 | COAT LAB W/CUFFS BLUE 6XLARGE |
| 73635 | COAT LAB W/CUFFS WHITE 2XLARGE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73629 | 功能描述:COAT LAB W/SNAPS WHITE 6XLARGE RoHS:否 類別:靜電控制，ESD，無塵室產品 >> 衣物 系列:Statshield® 標準包裝:1 系列:Statshield® 服裝類型:外套，帶袖套 尺寸:6XLarge 材質:聚酯 顏色:青色 特點:胯部帶 4mm 卡釘，袖口帶導電織物 |
| 73629-P | 制造商:Molex 功能描述: |
| 73629-P-50 | 制造商:Molex 功能描述: |
| 7362BA | 功能描述:散熱片 1100-H14 AL. .8 in. X .71 in. RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| 7-362-BA | 功能描述:HEATSINK VERT HORZ W/TABS TO-220 RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:7 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環(huán)境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
發(fā)布緊急采購，3分鐘左右您將得到回復。