- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6521FE-IM/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QCC68 PDF資料下載
參數資料
| 型號： | 71M6521FE-IM/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 封裝： | LEAD FREE, LQFN-68 |
| 文件頁數： | 77/103頁 |
| 文件大小： | 1691K |
| 代理商： | 71M6521FE-IM/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
v1.1
2005-2010 Teridian Semiconductor Corporation
Page: 75 of 103
A Maxim Integrated Products Brand
19-5370; 10/10
FLSH_ERASE[7:0]
SFR94[7:0]
0
W
Flash Erase Initiate
FLSH_ERASE is used to initiate either the Flash Mass Erase cycle or
the Flash Page Erase cycle. Specific patterns are expected for
FLSH_ERASE in order to initiate the appropriate Erase cycle.
(default = 0x00).
0x55 – Initiate Flash Page Erase cycle. Must be proceeded by
a write to FLSH_PGADR @ SFR 0xB7.
0xAA – Initiate Flash Mass Erase cycle. Must be proceeded by a
write to FLSH_MEEN @ SFR 0xB2 and the debug (CC)
port must be enabled.
Any other pattern written to FLSH_ERASE will have no effect.
FLSH_MEEN
SFRB2[1]
0
W
Mass Erase Enable
0 – Mass Erase disabled (default).
1 – Mass Erase enabled.
Must be re-written for each new Mass Erase cycle.
FLSH_PGADR[6:0]
SFRB7[7:1]
0
W
Flash Page Erase Address
FLSH_PGADR[6:0] – Flash Page Address (page 0 thru 127) that will
be erased during the Page Erase cycle. (default = 0x00).
Must be re-written for each new Page Erase cycle.
FLSH_PWE
SFRB2[0]
0
R/W
Program Write Enable
0 – MOVX commands refer to XRAM Space, normal operation
(default).
1 – MOVX @DPTR,A moves A to Program Space (Flash) @ DPTR.
This bit is automatically reset after each byte written to flash. Writes
to this bit are inhibited when interrupts are enabled.
FOVRIDE
20FD[4]
0
R/W
Permits the values written by MPU to temporarily override the values
in the fuse register (reserved for production test).
IE_FWCOL0
IE_FWCOL1
SFRE8[2]
SFRE8[3]
0
R/W
Interrupt flags for Firmware Collision Interrupt. See Flash Memory
Section for details.
IE_PB
SFRE8[4]
0
--
R/W
PB flag. Indicates that a rising edge occurred on PB. Firmware must
write a zero to this bit to clear it. The bit is also cleared when MPU
requests SLEEP or LCD mode. On bootup, the MPU can read this
bit to determine if the part was woken with the PB DIO0[0].
IE_PLLRISE
SFRE8[6]
0
R/W
Indicates that the MPU was woken or interrupted (int 4) by System
power becoming available, or more precisely, by PLL_OK rising.
Firmware must write a zero to this bit to clear it
IE_PLLFALL
SFRE8[7]
0
R/W
Indicates that the MPU has entered BROWNOUT mode because
System power has become unavailable (int 4), or more precisely,
because PLL_OK fell.
Note: this bit will not be set if the part wakes into
BROWNOUT mode because of PB or the WAKE timer.
Firmware must write a zero to this bit to clear it.
IE_XFER
IE_RTC
SFRE8[0]
SFRE8[1]
0
R/W
Interrupt flags. These flags monitor the XFER_BUSY interrupt and
the RTC_1SEC interrupt. The flags are set by hardware and must
be cleared by the interrupt handler. Note that IE6, the interrupt 6
flag bit in the MPU must also be cleared when either of these
interrupts occur.
IE_WAKE
SFRE8[5]
0
--
R/W
Indicates that the MPU was woken by the autowake timer. This bit
is typically read by the MPU on bootup. Firmware must write a zero
to this bit to clear it
INTBITS
SFRF8[6:0]
--
R/W
Interrupt inputs. The MPU may read these bits to see the input to
external interrupts INT0, INT1, up to INT6. These bits do not have
any memory and are primarily intended for debug use.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6521FE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6531D-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532D-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6532F-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6531D-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6521FE-IMR | 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC |
| 71M6521FE-IMR/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6521-TGP1-68M | 制造商:Maxim Integrated Products 功能描述:Programmer Accessories Gang Programmer Base w/6521 Socket Brd |
| 71M6523-DB | 功能描述:開發板和工具包 - 8051 71M6521D Demo Brd RoHS:否 制造商:Silicon Labs 產品:Development Kits 工具用于評估:C8051F960, Si7005 核心: 接口類型:USB 工作電源電壓: |
| 71M6523-IM | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。