- 您現在的位置：買賣IC網 > PDF目錄360322 > 7152MI11 Spread Spectrum Clock Generator PDF資料下載
參數資料
| 型號： | 7152MI11 |
| 英文描述： | Spread Spectrum Clock Generator |
| 中文描述： | 擴頻時鐘發生器 |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 115K |
| 代理商： | 7152MI11 |
Spread Spectrum Clock Generator
MDS 7152 E
3
Revision 012306
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICS7152
External Components
The ICS7152 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01μF must be connected
between GND and VDD on pin 6, as close to this pin as
possible. For optimum device performance, the
decoupling capacitor should be mounted on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
Series termination should be used on the clock output.
To series terminate a 50
trace (a commonly used
trace impedance) place a 27
resistor in series with
the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
25
.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed
away from the ICS7152. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
Crystal Information
The crystal used should be a fundamental mode,
parallel resonant. Crystal capacitors should be
connected from pins X1 to ground and X2 to ground to
optimize the initial accuracy. The value of these
capacitors is given by the following equation:
Crystal caps (pF) = (C
L
- 6) x 2
In the equation, C
L
is the crystal load capacitance. So,
for a crystal with a 16 pF load capacitance, two 20 pF
[(16-6) x 2] capacitors should be used.
Spread Spectrum Profile
The ICS7152 low EMI clock generator uses a triangular
frequency modulation profile for optimal down stream
tracking of zero delay buffers and other PLL devices.
The frequency modulation amplitude is constant with
variations of the input frequency.
Time
F
Modulation Rate
相關PDF資料 |
PDF描述 |
|---|---|
| 7152MI12 | Spread Spectrum Clock Generator |
| 7152I01L | Spread Spectrum Clock Generator |
| 7152I02L | Spread Spectrum Clock Generator |
| 7152I11L | Spread Spectrum Clock Generator |
| 7152I12L | Spread Spectrum Clock Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7152MI-11LF | 功能描述:時鐘發生器及支持產品 SPREAD SPECTRUM CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 7152MI-11LFT | 功能描述:時鐘發生器及支持產品 SPREAD SPECTRUM CLOCK GENERATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| 7152MI12 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Generator |
| 7152MI-12LF | 功能描述:IC CLOCK GENERATOR 8-SOIC 制造商:idt, integrated device technology inc 系列:- 包裝:管件 零件狀態:過期 類型:擴展頻譜時鐘發生器 PLL:是 輸入:時鐘 輸出:CMOS 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大值:134MHz 分頻器/倍頻器:無/是 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:97 |
| 7152MI-12LFT | 功能描述:IC CLOCK GENERATOR 8-SOIC 制造商:idt, integrated device technology inc 系列:- 包裝:帶卷（TR） 零件狀態:過期 類型:擴展頻譜時鐘發生器 PLL:是 輸入:時鐘 輸出:CMOS 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大值:134MHz 分頻器/倍頻器:無/是 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:2,500 |
發布緊急采購，3分鐘左右您將得到回復。