- 您現在的位置：買賣IC網 > PDF目錄360322 > 7151MI10 Spread Spectrum Clock Generator PDF資料下載
參數資料
| 型號： | 7151MI10 |
| 英文描述： | Spread Spectrum Clock Generator |
| 中文描述： | 擴頻時鐘發生器 |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 113K |
| 代理商： | 7151MI10 |
Spread Spectrum Clock Generator
MDS 7151 E
3
Revision 012306
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICS7151
External Components
The ICS7151 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01μF must be connected
between GND and VDD on pin 7, as close to this pin as
possible. For optimum device performance, the
decoupling capacitor should be mounted on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
Series termination should be used on the clock output.
To series terminate a 50
trace (a commonly used
trace impedance) place a 27
resistor in series with
the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
25
.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01μF decoupling capacitor should be mounted
on the component side of the board as close to the
VDD pin as possible. No vias should be used between
the decoupling capacitor and VDD pin. The PCB trace
to VDD pin should be kept as short as possible, as
should the PCB trace to the ground via.
2) To minimize EMI, the 27
series termination resistor
(if needed) should be placed close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed
away from the ICS7151. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
Crystal Information
The crystal used should be a fundamental mode (do
not use third overtone), parallel resonant. Crystal
capacitors should be connected from pins X1 to ground
and X2 to ground to optimize the initial accuracy. The
value of these capacitors is given by the following
equation:
Crystal caps (pF) = (C
L
- 6) x 2
In the equation, C
L
is the crystal load capacitance. So,
for a crystal with a 16 pF load capacitance, two 20 pF
[(16-6) x 2] capacitors should be used.
Spread Spectrum Profile
The ICS7151 low EMI clock generator uses a triangular
frequency modulation profile for optimal down stream
tracking of zero delay buffers and other PLL devices.
The frequency modulation amplitude is constant with
variations of the input frequency.
Time
F
Modulation Rate
相關PDF資料 |
PDF描述 |
|---|---|
| 7151MI20 | Spread Spectrum Clock Generator |
| 7151MI40 | Spread Spectrum Clock Generator |
| 7151MI50 | Spread Spectrum Clock Generator |
| 7152AM02 | Spread Spectrum Clock Generator |
| 7152AM11 | Spread Spectrum Clock Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 7151MI20 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Generator |
| 7151MI40 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Generator |
| 7151MI50 | 制造商:ICS 制造商全稱:ICS 功能描述:Spread Spectrum Clock Generator |
| 7152 | 功能描述:燈 5.0V .115A RoHS:否 制造商:Chicago Miniature 燈類型:Incandescent 燈座類型:Wire Terminal 燈大小:T-1 3/4 顏色: 電壓:14 V 工作電流: MSCP:0.3 MSCP 壽命:40000 hr 封裝:Bulk |
| 71520 | 功能描述:BIT TORX 1/4" T20 25MM RoHS:否 類別:工具 >> 螺釘和螺母驅動器 - 刀片和位 系列:- 標準包裝:1 系列:TorqueVario™ 類型:十字槽刀片 尺寸:#2 長度:7.48"（190mm） 特點:絕緣達 10,000V 重量:0.07 磅（31.75g） |
發布緊急采購，3分鐘左右您將得到回復。