12
Notes:
1. Each channel.
2. CURRENT TRANSFER RATIO is dened as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%.
3. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
4. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode
pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level
is the maximum tolerable (negative) dVCM/dt on the falling edge of the common mode pulse signal, VCM, to assure that the output will remain
in a Logic Low state (i.e., VO < 0.8 V).
6. The 1.9 k
Ω load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
7. The 4.1 k
Ω load represents 1 LSTTL unit load of 0.36 mA and the 6.1 kΩ pull-up resistor.
8. The frequency at which the ac output voltage is 3 dB below the low frequency asymptote.
9. Use of a 0.1
μF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for 1 second (leakage detec-
tion current limit, II-O ≤5
μA).
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for 1 second (leakage detec-
tion current limit, II-O ≤5
μA).
12. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
13. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/ °C for the SOIC-8 package.
Figure 1. DC and pulsed transfer characteristics.
Figure 2. Current transfer ratio vs. input current.
Figure 3. Input current vs. forward voltage.
0
10
20
VO – OUTPUT VOLTAGE – V
I O
–
OUTPUT
CURRENT
–
mA
10
5
0
T = 25°C
V
= 5.0 V
A
CC
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
I = 5 mA
F
NORMALIZED
I = 16 mA
V = 0.5 V
V
= 5 V
T = 25°C
F
O
CC
A
HCPL-2530/0530
HCPL-2531/0531/4534/0534
1.5
1.0
0.5
0.1
0
1
10
100
NORMALIZED
CURRENT
TRANSFER
RATIO
IF – INPUT CURRENT – mA
VF – FORWARD VOLTAGE – VOLTS
100
10
0.1
0.01
1.1
1.2
1.3
1.4
I F
–
FORWARD
CURRENT
–
mA
1.6
1.5
1.0
0.001
1000
IF
VF
+
T = 25°C
A
–
Figure 4. Current transfer ratio vs. temperature.
Figure 5. Propagation delay vs. temperature.
Figure 6. Logic high output current vs. tempera-
ture.
-50
+50
TA – TEMPERATURE – °C
I
OH
–
LOGIC
HIGH
OUTPUT
CURRENT
–
nA
10 -2
-25
0
+25
+75
+100
10 -1
10 0
10+1
10+2
10+3
10+4
VO = VCC = 5.0 V
IF = 0
1.1
1.0
0.9
0.8
0.7
0.6
-60
-20
0
80
NORMALIZED
CURRENT
TRANSFER
RATIO
TA – TEMPERATURE – °C
F
CC
A
-40
20
40
60
100
O
NORMALIZED
I = 16 mA
V = 0.5 V
V
= 5 V
T = 25°C
HCPL-2530/0530
HCPL-2531/0531/4534/0534
2000
1500
1000
500
0
-60
-20
20
60
100
TA – TEMPERATURE – °C
t P
–
PROPAGATION
DELAY
–
ns
tPHL
tPLH
IF = 16 mA, VCC = 5.0 V
HCPL-2530/0530 (RL = 4.1 kΩ)
HCPL-2531/0531/4534/0534
(RL = 1.9 kΩ)