- 您現在的位置：買賣IC網 > PDF目錄7099 > 66166 (Desco)VINYL DARKBLU 2LAYER .060X24X48" PDF資料下載
參數資料
| 型號： | 66166 |
| 廠商： | Desco |
| 文件頁數： | 2/4頁 |
| 文件大?。?/td> | 0K |
| 描述： | VINYL DARKBLU 2LAYER .060X24X48" |
| 其它有關文件： | Mat Selection Chart |
| 標準包裝： | 1 |
| 系列： | Statfree B2™ |
| 墊子類型： | 桌子，工作臺 |
| 形狀： | 矩形 |
| 長度： | 4'（1.22m） |
| 寬： | 2'（0.61m） |
| 厚度： | 0.06" (1.52mm) |
| 顏色： | 深藍色 |
| 材質： | 乙烯基 |
| 特點： | 耗散 |
| 包括： | 接地軟線，接地卡扣套件 |
| 其它名稱： | 16-1122 |
TB-2000 Page 2 of 4
Grounding Methods
Method 1 (Grounding via ground cords)
1. Desco recommends using a common point ground cord when
grounding via ground cords. Most common point ground cords
will ground your ESD worksurface and provide banana jack
ground points for two wrist straps.
2. A common point ground should be installed at each workstation
and should be connected directly to a verified “green wire”
equipment ground. Only one groundable point should exist on a
worksurface.
Figure 5. Common point ground for each workstation.
3. Wrist straps should never be grounded through a worksurface,
as the added resistance of the worksurface material will
prevent the wrist strap from operating properly.
Figure 6. Proper grounding of wrist straps.
4. Per ANSI/ESD S1.1, a current limiting resistor in the wrist strap
ground cord is recommended. If other than a one megohm
resistor, special marking in red is required.
For additional information on grounding we recommend Desco
Technical Bulletin TB-2007.
Groundable Point Installation
1. Before installing a groundable point on your mat you must first
determine whether you will need a snap socket or stud, the
type of snap hardware and the location.
2. Desco has three types of 10mm (.395") field installable mat
grounding snaps. The first type is a screw-on snap kit Desco
item number 09864 Universal Snap Kit.
A. Determine the position of the grounding snap (one only
per mat) and type of fastener you will be installing (socket
or stud). Take precautions not to cut your hand, and punch
a hole through the material with a small Phillips screwdriver
or awl.
B. Remove the release paper from the circular common point
ground label and affix it so that it aligns with the hole on the
material.
C. Select one of the screws as follows:
Material less than .100" thick - short screw
Material greater than .100" thick - long screw
D. Insert the screw through the top on the snap stud or socket,
the washer, the label and the material. Affix the assembly
with the conical nut supplied with the kit and tighten down
the screw using a Phillips screwdriver.
E. Remaining will be either a 10mm stud or socket, and either
a long or short screw to be discarded or saved for another
application.
ASSEMBLE
SCREW, STUD,
WASHER, LABEL
AND CONICAL NUT
AS SHOWN
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
WRONG!
RIGHT!
Figure 8. Installing Universal Snap Kit on mat.
USE A PHILLIPS
SCREWDRIVER OR
AWL TO PUNCH
A HOLE IN THE
MATERIAL
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 7. Three kinds of snaps.
3. The second type of mat grounding snap is the push and
clinch snap. This snap is designed for use with any type of
soft mat material: dissipative, conductive or multi-layered. It is
recommended for use with three-layered material, because it
provides excellent contact with the internal conductive scrim
layer. It is recommended that before inserting this snap, the
mat be punctured with a sharp tool where the snap will be
placed. Take precautions not to cut your hand. Push and Clinch
snaps are available as a snap stud as item #09861 and as a
snap socket as item #09863.
A. Remove the release paper from the circular label and
affix it onto the mat material in the desired location.
B. Center the prongs on the snap assembly with the label.
Apply pressure to the snap until the prongs come through
the back of the mat, then clinch over prongs to secure snap
as shown in Figure 9.
相關PDF資料 |
PDF描述 |
|---|---|
| RZ03-1A4-D024 | RELAY GEN PURPOSE SPST 16A 24V |
| 325308-25-0 | TERM BARRIER 25CIRC SGL ROW .325 |
| 325140-22-0 | TERM BARRIER 22CIRC SGL ROW .325 |
| RZ01-1C4-D024 | RELAY GEN PURPOSE SPDT 12A 24V |
| 325130-22-0 | TERM BARRIER 22CIRC SGL ROW .325 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 66167 | 功能描述:VINYL DARKBLU 2LAYER .060X30X60" RoHS:否 類別:靜電控制，ESD，無塵室產品 >> 接地墊 系列:Statfree B2™ 標準包裝:1 系列:Statfree B2™ 墊子類型:桌子，工作臺卷筒 形狀:矩形 長度:50' (15.24m) 寬:2'（0.61m） 厚度:0.06" (1.52mm) 顏色:深藍色 材質:橡膠 特點:導電，靜電耗散 包括:- |
| 66167-009 | 制造商:FCI 功能描述:SUB D PLUG PLASTIC 9 POS |
| 66167-015 | 制造商:FCI 功能描述:SUB D PLUG PLASTIC 15 POS |
| 66167-025 | 制造商:FCI 功能描述:SUB D PLUG PLASTIC 25 POS |
| 66167-037 | 制造商:FCI 功能描述:SUB D PLUG PLASTIC 37 POS |
發布緊急采購，3分鐘左右您將得到回復。