參數資料
型號: 5962-9320601MEA
廠商: TEXAS INSTRUMENTS INC
元件分類: 電源管理
英文描述: 1-CHANNEL POWER SUPPLY SUPPORT CKT, CDIP16
封裝: DIP-16
文件頁數: 6/8頁
文件大小: 163K
代理商: 5962-9320601MEA
UC1907, UC2907, UC3907
LOAD SHARE CONTROLLER
SLUS165B – MARCH 1999 - REVISED MAY 2001
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
pin assignments
Adjust Amplifier: (Pins 13, 14, 15) This amplifier adjusts the individual module’s reference voltage to maintain
equal-current sharing. It is a transconductance type in order that its bandwidth may be limited and noise kept
out of the reference-adjust circuitry, with a simple capacitor to ground. The function of this amplifier is to compare
its own module-output current to the share-bus signal, which represents the highest output current. This will
force an adjust command which is capable of increasing the reference voltage as seen by the voltage amplifier
by as much as 100 mV. This number stems from the 17.5:1 internal resistor ratio between the adjust amplifier’s
clamped output and the reference, and represents a 5% total range of adjustment. This value should be
adequate to compensate for unit-to-unit reference and external-resistor tolerances. The adjust amplifier has a
built-in 50-mV offset on its inverting input which will force the unit acting as the master to have a low output,
resulting in no change to the reference. While this 50-mV offset represents an error in current sharing, the gain
of the current amplifier reduces it to only 2.5 mV across the current-sense resistor. It should also be noted that
when the module is acting independently with no connection to the share bus node, or when the share bus node
is shorted to ground, its reference voltage will be unchanged. Since only the circuit acting as a master will have
a low output from the adjust amplifier, this signal is used to activate a flag output to identify the master, should
some corrective action be needed.
Status Indicate: (Pin 16) This pin is an open-collector output intended to indicate the unit which is acting as
the master. It achieves this by sensing when the adjust amp is in its low state and pulling the status-indicate pin
low.
additional information
Please refer to additional application information.
1.
By Mark Jordan, UC3907 Load Share IC Simplifies Parallel Power Supply Design, TI Literature Number
SLUA147.
2.
By Laszlo Balogh, UC3902 Load Share Controller and its Performance in Distributed Power Systems, TI
Literature Number SLUA128.
UDG-94103
Figure 1. Load System Diagram
相關PDF資料
PDF描述
5962-9320901MPX DUAL OP-AMP, 2000 uV OFFSET-MAX, CDIP8
5962-9321501Q2A STEPPER MOTOR CONTROLLER, 0.5 A, CQCC20
5962-9321501QEA STEPPER MOTOR CONTROLLER, 0.5 A, CDIP16
5962-9325501M2A QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, CQCC20
5962-9325503M2A QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, CQCC20
相關代理商/技術參數
參數描述
5962-9321101MCA 功能描述:總線接收器 RoHS:否 制造商:Texas Instruments 接收機數量:4 接收機信號類型:Differential 接口類型:EIA/TIA-422-B, V.11 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TSSOP-16 封裝:Reel
5962-9321201MPA 制造商:Linear Technology 功能描述:SMD (STD. MIL DWG.) LT1111MJ8
5962-9321401MEA 制造商:Analog Devices 功能描述:V-Ref Programmable 制造商:Analog Devices 功能描述:V-Ref Programmable ±10V 10mA 16-Pin CDIP Tube 制造商:Analog Devices 功能描述:V-REF PROGRAMMABLE 10V 10MA 16CDIP - Rail/Tube 制造商:Analog Devices Inc. 功能描述:Voltage & Current References IC MONO +/-10V REFERENCE 制造商:Analog Devices Inc. 功能描述:IC MONO +/-10V REFERENCE
5962-9321601QPA 制造商:Texas Instruments 功能描述:OP Amp Single GP 制造商:Rochester Electronics LLC 功能描述:- Bulk
5962-9321602QPA 制造商:Texas Instruments 功能描述:OP Amp Single GP ±22V/44V 8-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:OP AMP SGL GP 22V/44V 8CDIP - Rail/Tube