- 您現在的位置：買賣IC網 > PDF目錄371606 > 522979E Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits PDF資料下載
參數資料
| 型號： | 522979E |
| 英文描述： | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 中文描述： | 集成電路 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 292K |
| 代理商： | 522979E |
11
LT1185
APPLICATIOU
Thermal Regulation
IC regulators have a regulation term not found in discrete
designs because the power transistor is thermally coupled
to the reference. This creates a shift in the output voltage
which is proportional to power dissipation in the regulator.
U
W
U
V
OUT
= P(K1 + K2
θ
JA
)
= (I
OUT
)(V
IN
– V
OUT
)(K1 + K2
θ
JA
)
K1 and K2 are constants. K1 is a fast time constant effect
caused by die temperature gradientswhich are estab-
lished within 50ms of a power change. K1 is specified on
the data sheet as thermal regulation, in percent per watt.
K2 is a long time constant term caused by the temperature
drift of the regulator reference voltage. It is also specified,
but in percent per degree centigrade. It must be multiplied
by overall thermal resistance, junction-to-ambient,
θ
JA
.
As an example, assume a 5V regulator with an input
voltage of 8V, load current of 2A, and a total thermal
resistance of 4
°
C/W, including junction-to-case, (use
control area specification), interface, and heat sink resis-
tance. K1 and K2, respectively, from the data sheet are
0.014%/W and 0.01%/
°
C.
V
OUT
= (2A)(8V – 5V)(0.014 + 0.01
×
4)
= 0.32%
This shift in output voltage could be in either direction
because K1 and K2 can be either positive or negative.
Thermal regulation is already included in the worst case
reference specification.
Output Voltage Reversal
Some IC regulators suffer from a latch-up state when their
output is forced to a reverse voltage of as little as one diode
drop. The latch-up state can be triggered without a fault
condition when the load is connected to an opposite
polarity supply instead of to ground. If the second supply
is turned on first, it will pull the output of the first supply
to a reverse voltage through the load. The first supply may
then latch off when turned on. This problem is particularly
annoying because the diode clamps which should always
be used to protect against polarity reversal do not usually
stop the latch-up problem.
The LT1185 is designed to allow output reverse polarity of
several volts without damage or latch-up, so that a simple
diode clamp can be used.
相關PDF資料 |
PDF描述 |
|---|---|
| 522980H | IC |
| 522981F | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 522982D | IC-OFFLINE SWITCHING REGULATOR |
| 522983B | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 522984X | IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 522980H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| 522981F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| 522982D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-OFFLINE SWITCHING REGULATOR |
| 522983B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| 522984X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。