- 您現在的位置：買賣IC網 > PDF目錄371605 > 522971X IC PDF資料下載
參數資料
| 型號： | 522971X |
| 英文描述： | IC |
| 中文描述： | 集成電路 |
| 文件頁數： | 6/16頁 |
| 文件大小： | 292K |
| 代理商： | 522971X |
6
LT1185
APPLICATIOU
Amplifier A2 is used to generate an internal current through
Q4 when an external resistor is connected from the REF
pin to ground. This current is equal to 2.37V divided by
R
LIM
. It generates a current limit sense voltage across R1.
The regulator will current limit via A4 when the voltage
across R2 is equal to the voltage across R1. These two
resistors essentially form a current “amplifier” with a gain
of 350/0.055 = 6,360. Good temperature drift is inherent
because R1 and R2 are made from the same diffusions.
Their ratio, not absolute value, determines current limit.
Initial accuracy is enhanced by trimming R1 slightly at
wafer level. Current limit is equal to 15k
/R
LIM
.
D1 and I1 are used to guarantee regulator shutdown when
REF pin current drops below 2
μ
A. A current less than 2
μ
A
through Q4 causes the + input of A5 to go low and shut
down the regulator via D2.
A3 is an internal current limit amplifier which can override
the external current limit. It provides “goof proof” protec-
tion for the pass transistor. Although not shown, A3 has
a nonlinear foldback characteristic at input-output volt-
ages above 12V to guarantee safe area protection for Q3.
See the graph, Internal Current Limit in the Typical Perfor-
mance Characteristics of this data sheet.
U
W
U
Setting Output Voltage
The LT1185 output voltage is set by two external resistors
(see Figure 2). Internal reference voltage is trimmed to
2.37V so that a standard 1% 2.37k resistor (R1) can be
used to set divider current at 1mA. R2 is then selected
from:
for R1 = 2.37k and V
REF
= 2.37V, this reduces to:
R2 = V
OUT
– 2.37k
suggested values of 1% resistors are shown.
V
OUT
5V
5.2V
6V
12V
15V
R2 WHEN R1 = 2.37k
2.67k
2.87k
3.65k
9.76k
12.7k
Output Capacitor
The LT1185 has a collector output NPN pass transistor,
which makes the open-loop output impedance much
higher than an emitter follower. Open-loop gain is a direct
function of load impedance, and causes a main-loop
“pole” to be created by the output capacitor, in addition to
an internal pole in the error amplifier. To ensure loop
stability, the output capacitor must have an ESR (effective
series resistance) which has an upper limit of 2
, and a
lower limit of 0.2 divided by the capacitance in
μ
F. A 2
μ
F
output capacitor, for instance, should have a maximum
ESR of 2
, and a minimum of 0.2/2 = 0.1
. These values
are easily encompassed by standard solid tantalum ca-
pacitors, but occasionally a solid tantalum unit will have
abnormally high ESR, especially at very low temperatures.
The suggested 2
μ
F value shown in the circuit applications
should be increased to 4.7
μ
F for –40
°
C and –55
°
C de-
signs if the 2
μ
F units cannot be guaranteed to stay below
2
at these temperatures.
Although solid tantalum capacitors are suggested, other
types can be used if they meet the ESR requirements.
Standard aluminum electrolytic capacitors need to be
upward of 25
μ
F in general to hold 2
maximum ESR,
especially at low temperatures. Ceramic, plastic film, and
monolithic capacitors have a problem with ESR being too
low These types should have a 1
carbon resistor in
series to guarantee loop stability.
The output capacitor should be located close to the regu-
lator (
≤
3") to avoid excessive impedance due to lead
inductance. A six inch lead length (2
×
3") will generate an
extra 0.8
inductive reactance at 1MHz, and unity-gain
frequency can be up to that value.
For remote sense applications, the capacitor should still be
located close to the regulator. Additional capacitance can
be added at the remote sense point, but the remote
capacitor must be at least 2
μ
F solid tantalum. It cannot be
a low ESR type like ceramic or mylar unless a 0.5
to 1
carbon resistor is added in series with the capacitor. Logic
boards with multiple low ESR bypass capacitors should
have a solid tantalum unit added in parallel whose value is
approximately five times the combined value of low ESR
capacitors.
R2 = (V
OUT
– 2.37) R1
V
REF
相關PDF資料 |
PDF描述 |
|---|---|
| 522976X | IC |
| 522977R | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 522978G | IC-SWITCHING REGULATOR |
| 522979E | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 522980H | IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 522975B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC CMOS OPERATIONSVERSTAERKER |
| 522976X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| 522977R | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
| 522978G | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-SWITCHING REGULATOR |
| 522979E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。