
M
em
or
y
4
0627.00Rev2
All data sheets are subject to change without notice
2000 Space Electronics Inc.
All rights reserved.
16-BIT, 20 KHZ A/D CONVERTER
5102ALPRP
Power Consumption 11, 12
(SLEEP High)
(SLEEP Low)
P
do
P
ds
--
85
45
130
--
mW
Power Supply Rejection 13
Positive Supplies
Negative Supplies
PSR
--
84
--
dB
1. Minimum resolution for which no missing codes are guaranteed over the specified temperature range.
2. Applies after calibration at any temperature within the specified temperature range.
3. Total drift over specified temperature range after calibration at power-up at 25°C.
4. Guaranteed by characterization (5102A die).
5. Wideband noise aliased into the baseband. Referred to the input.
6. Applied only in the track mode. When converting or calibrating, input capacitance will not exceed 30 pF.
7. Conversion time scales directly to the master clock speed. The times shown are for synchronous, internal loopback (FRN mode). In PDT, RBT, and SSC modes, asyn-
chronrous delay between the falling edge of HOLD and the start of conversion may add to the apparent conversion time. This delay will not exceed 1 master clock
cycle + 140 ns.
8. The 5102ALPRP requires 6 clock cycles of coarse charge, followed by a minimum of 5.625 s of fine charge. FRN mode allows 9 clock cycles for fine charge which
provides for the minimum 5.625 s with a 1.6 MHz clock; however, in PDT, RBT, or SSC modes, at clock frequencies less than 1.6 MHz, fine charge may be less than 9
clock cycles.
9. Throughput is the sum of the acquisition and conversion times. It will vary in accordance with conditions affecting acquisition and conversion times described above.
10. Typical value (measured).
11. All outputs unloaded. All inputs at VD+ or DGND.
12. Power consumption in the sleep mode applies with no master clock applied (CLKIN held high or low).
13. With 300 mV p-p, 1 kHz ripple applied to each supply separately in the bipolar mode. Rejection improves by 6 dB in the unipolar mode to 90 dB.
TABLE 4. 5102ALPRP SWITCHING CHARACTERISTICS
(T
A = TMIN
TO
T
MAX; VA+, VD+ = 5V ± 10%; VA-, VD- = -5V ± 10%; I
NPUTS
: LOGIC 0 = 0V, LOGIC 1 = VD+; C
L = 50
P
F)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
CLKIN Period 1, 2
t
clk
0.5
--
10
s
CLKIN Low Time
t
clkl
200
--
ns
CLKIN High Time
t
clkh
200
--
ns
Crystal Frequency 1, 2
f
xtal
--
1.6
--
MHz
SLEEP Rising to Oscillator Stable 3
--
20
--
ms
RST Pulse Width 4
t
rst
150
--
ns
RST to STBY Falling
t
drrs
--
100
--
ns
RST Rising to STBY Rising
t
cal
--
2,882,040
--
tclk
CH1/2 Edge to TRK1, TRK2 Rising 5
t
drsh1
--
80
--
ns
CH1/2 Edge to TRK1, TRK2 Falling 5
t
dfsh4
--
68t
clk + 260
ns
TABLE 3. ANALOG CHARACTERISTICS
(T
A = TMIN
TO
T
MAX; VA+, VD+ = 5V; VA-, VD- = -5V; VREF = 4.5V; F
ULL
-SCALE INPUT SINEWAVE, 200 HZ; CLKIN = 1.6 MHZ; f
S = 20
K
HZ; BIPOLAR MODE;
FRN MODE; AIN1 AND AIN2 TIED TOGETHER, EACH CHANNEL TESTED SEPARATELY; ANALOG SOURCE IMPEDANCE = 50
WITH 1000 PF TO AGNDUNLESS OTHERWISE SPECIFIED)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT