- 您現在的位置：買賣IC網 > PDF目錄33783 > 44608P40 (ON SEMICONDUCTOR) Few External Components Reliable Flexible GreenLine Very High Voltage PWM Controller PDF資料下載
參數資料
| 型號： | 44608P40 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Few External Components Reliable Flexible GreenLine Very High Voltage PWM Controller |
| 中文描述： | 很少的外部元件的可靠靈活二七二三六七六七高電壓PWM控制器 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 266K |
| 代理商： | 44608P40 |
MC44608
http://onsemi.com
7
Figure 5.
Vcont
2.4 V
Iprim
DMG
Clock
OSC
4 V
The OSC and Clock signals are provided according to the
Figure 5. The Clock signals correspond to the CT capacitor
discharge. The bottom curve represents the current flowing
in the sense resistor Rcs. It starts from zero and stops when
the sawtooth value is equal to the control voltage Vcont. In
this way the SMPS is regulated with a voltage mode control.
Overvoltage Protection
The MC44608 offers two OVP functions:
– a fixed function that detects when VCC is higher than
15.4V
– a programmable function that uses the demag pin. The
current flowing into the demag pin is mirrored and
compared to the reference current Iovp (120
A). Thus this
OVP is quicker as it is not impacted by the VCC inertia and
is called QOVP.
In both cases, once an OVP condition is detected, the
output is latched off until a new circuit START–UP.
Start–up Management
The Vi pin 8 is directly connected to the HV DC rail Vin.
This high voltage current source is internally connected to
the VCCpinandthusisusedtochargetheVCCcapacitor.The
VCC capacitor charge period corresponds to the Start–up
phase. When the VCC voltage reaches 13V, the high voltage
9mA current source is disabled and the device starts
working. The device enters into the switching phase.
It is to be noticed that the maximum rating of the Vi pin 8
is 700V. ESD protection circuitry is not currently added to
this pin due to size limitations and technology constraints.
Protection is limited by the drain–substrate junction in
avalanche breakdown. To help increase the application
safety against high voltage spike on that pin it is possible to
insert a small wattage 1k
W series resistor between the Vin
rail and pin 8.
The Figure 6 shows the VCC voltage evolution in case of
no external current source providing current into the VCC
pin during the switching phase. This case can be
encountered in SMPS when the self supply through an
auxiliary winding is not present (strong overload on the
SMPS output for example). The Figure 16 also depicts this
working configuration.
Figure 6. Hiccup Mode
Start–up
Latched off
Phase
Switching
Phase
V
CC
6.5 V
10 V
13 V
In case of the hiccup mode, the duty cycle of the switching
phase is in the range of 10%.
Mode Transition
The LW latch Figure 7 is the memory of the working status
at the end of every switching sequence.
Two different cases must be considered for the logic at the
termination of the SWITCHING PHASE:
1. No Over Current was observed
2. An Over Current was observed
These 2 cases are corresponding to the signal labelled
NOC in case of “No Over Current” and “OC” in case of Over
Current. So the effective working status at the end of the ON
time memorized in LW corresponds to Q=1 for no over
current and Q=0 for over current.
This sequence is repeated during the Switching phase.
Several events can occur:
1. SMPS switch OFF
2. SMPS output overload
3. Transition from Normal to Pulsed Mode
4. Transition from Pulsed Mode to Normal Mode
Figure 7. Transition Logic
&
I
SQ
R
LW
+
–
&
CS
Q
&
R2
Q
S
Mode
LEB out
1 V
VPWM
OUT
Stand–by
R1
Start–up
Phase
Switching
Phase
Start–up
Phase
NOC
OC
> 24 A
m
Latched Off
Phase
&
demag
S1
Switch
1. SMPS SWITCH OFF
When the mains is switched OFF, so long as the bulk
electrolithic bulk capacitor provides energy to the SMPS,
the controller remains in the switching phase. Then the peak
current reaches its maximum peak value, the switching
frequency decreases and all the secondary voltages are
reduced. The VCC voltage is also reduced. When VCC is
equal to 10V, the SMPS stops working.
相關PDF資料 |
PDF描述 |
|---|---|
| 44620-0001 | Phone Connector,PCB Mnt,8 Contacts,PIN,PC TAIL Terminal,LOCKING MECH |
| 44620-0002 | Modular Jack; No. of Contacts:8; No. of Ports:1; Connector Body Material:Nylon; Mounting Type:PC Board; Series:RJ45 RoHS Compliant: Yes |
| 44620-0003 | RJ45 Inv Modjack w/Keepout Featureoffset |
| 44661-0001 | Modjack RA Compact Cat 5 PTH Shielded RoHS Compliant: Yes |
| 44661-0002 | Modular Connector; No. of Contacts:8; No. of Ports:1; Body Material:PA Polyamide (Nylon), Glass-filled; Color:Black; Contact Termination:Through Hole; Mounting Type:Thru-Hole; Body Style:Right Angle; Current Rating:1.5A RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4460B5CBS | 制造商:Texas Instruments 功能描述: |
| 4460BCBS | 制造商:Texas Instruments 功能描述:- Trays |
| 4460CPCE10D434 | 功能描述:WIRELESS RF DEVEL KIT 制造商:silicon labs 系列:EZRadioPRO? 零件狀態:在售 類型:收發器 頻率:434MHz 配套使用產品/相關產品:Si4460 所含物品:板 標準包裝:1 |
| 4460CPCE27E169S | |
| 4460CPCE30E915S | 功能描述:WIRELESS RF DEVEL KIT 制造商:silicon labs 系列:EZRadioPRO? 零件狀態:在售 類型:收發器 頻率:915MHz 配套使用產品/相關產品:Si4460 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。